Question about Canon CLC 1150 Color Copier

1 Answer

CLC 3200 COPIER

My copier problem is when i refilled all catridges toner it is indicate toner low problem . I do not know how to i install or format the toner . If u have a solution to solve pls reply me . thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Canon Expert
  • 1,326 Answers

Do you have a CLC1150 or a CLC3200. If you have a 3200 you have to open the front door and go to the low toner color and unlock the lever and remove the toner cartridge and then open the new toner box and remove the orange tabs and install the new toner cart ridge and lock the lever and close the front door. You may have to wait till the copier catch's up with replenishing the toner and you are done. If you have a 1150 you have to open both front doors and on the left side of the hopper there is a black release lever, that will allow you to pull the hopper out to open the correct toner that is low. Opent the door and install the new toner bottle and remove the emptied toner bottle and push the hopper back into place and close the front doors. Good Luck

Posted on Nov 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After refilling toner powder in konicaminolta 1500w led shows please install a new toner catridge


The toner cartridges have electronic chips on them that tell the copier when they are used up since all you did was refill the cart and did nothing with the chip then copier still sees a used cart get a OEM cartridge install it correctly

Feb 17, 2014 | Konica Minolta PagePro Printers & Copiers

1 Answer

Hi Its says our toner is low on the workio 1820 photocoper.


low toner means you should refill toner in the catridge, if it has be refill it will stop.

Feb 07, 2011 | Panasonic Workio DP-1820E Copier

1 Answer

The machine copy a blank paper


Hi,i'll suggest you check the quantity of toner remaining in the printer,perhaps the toner is insufficient,if this is not the case,i'll suggest you check the printer catridges,probably they need to be replaced. If after these solution the problem persists,i'll suggest you contact the nearest printer technician for further diagnosis and assistance.
Thanks amd take care

Apr 16, 2010 | Canon CLC 1120 Color Copier

2 Answers

E020 01BO What does this error code mean?


E020 indicates a Black Toner malfunction. If you've recently changed the toner and failed to distribute the toner by gently shaking it from side to side, this could be the cause of this error or if the toner is very low it could trigger the same error.
01B0 is a drum error related to your toner error message. If toner cartridge is good, remove the cartridge, clean the drum, replace the cartridge and both errors should clear. A dirty drum will also trigger your 1st error e020.

Nov 16, 2009 | Canon CLC 1120 Color Copier

1 Answer

Copier won't print after refilling toner cartridge


As far as I know, filling up with toner is not enough. There is an electronic chip that must also be replaced, so the toner cartridge tells the unit it is a new one. Check with your supplier for such chip.

Oct 14, 2008 | Sharp AL 1631 Copier

2 Answers

E020 Error message on NP6050


A E020 code is a toner amount problem in the developing ass'y. Is the copier asking for toner or was it and no toner was installed? If not the amount of toner is to low for the hopper to add enough toner in to over ride the toner sensor. Look in the developing ass'y for toner, if you only see about a 1/8' of toner you need to clean or replace the toner sensor. Then you are going to have to run in service mode " toner-s". Then rechk the amount of toner in the developer ass'y. It should be about a 1/2' or so. If not you have a problem with the toner hopper. And if that is the problem you may want to manually add toner in the developing ass'y to get the copier working again. You also have to clear the error code in service mode.

Jan 28, 2008 | Canon CLC 1120 Color Copier

1 Answer

Xerox xc356 copier


TRY TO CLEAN THE RUBBER ON FEEDING PAPER WITH A DRY CLEAN CLOTH AND DROP A SOME ALCOHOL IN CLOTH AND CHECK THE PAPER PATH IF HAVE SOME A LITTLE PAPER ON PATH PAPER... ABOUT CATRIDGE...TRY TO REPLACE A NEW CATRIDGE.. DO THIS NECESSARY UR COPIER IS ON. panlaqui08@yahoo.com.ph

Jul 05, 2007 | Xerox XC356 Copier

Not finding what you are looking for?
Canon CLC 1150 Color Copier Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Printers & Copiers Experts

kakima

Level 3 Expert

96467 Answers

old marine
old marine

Level 3 Expert

1463 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...