Question about Saws

1 Answer

How to replace belt on 10'' Tilting Rockwell Delta Arbor Saw?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,176 Answers

I don't know the model number for your saw but you can go to and they have some information there that might be helpful. Note if your saw was made before 2000 they have a toll free number you can call to get the info requested. Hope this helps.

Posted on Jan 08, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The blade on my Delta 36-540 table saw is jammed in the 'down' position. The turn wheel will not move it. Thanks Walt

Is there a 'wheel lock' on the shaft? You may have to dismantle the saw arbor mechanism to free the worm gear drive. If the saw has been unused for a long time and exposed to excess moisture, the worm drive could have rusted tight. Good luck!

Feb 08, 2010 | Saws

1 Answer

How to change arbor and flange on delta unisaw. I would like to know if special tools required

You can change your arbor. See my Youtube short videos by searching delta arbor bearing. They detail removing the arbor bearings and installing new. This is the same process you would use to replace the arbor. There are special tools that I recommend.

Feb 03, 2010 | Delta Saws

1 Answer

I need to get a replacement saw blade guard for an old Rockwell Delta Radial arm saw. 12'' Blade Serial # MX3 2843 I don't know what model number this saw is to get the right part.

you can try going to and locating it that way but with only the serial number it would be impossible. Is there any numbers on it to indicate the model or partial model and you can pull up breakdowns that way.

Dec 10, 2009 | Delta Saws

1 Answer

I need a safety guard for rockwell radial arm saw serie 1555 serial #g-15809 where can I find one Thank -you Gilles

We not keeping the sawin the shop. we will buy a new one instead and give the rockwell saw to one employee. thank for your concern.

Nov 24, 2009 | Saws

1 Answer

Manual for #103.0205 circ. saw

Earlier comment 103.0205 Table Saws does not need lubrication is simply wrong.

The103.0202, 103.0203, 103.0305 Craftsman Companion Table Saws main Arbor axle DOES have to lubricated or else the axle bearing will quickly loosen side-to-side or vertically and fail to provide accurate saw cuts.

FWIW, Sears no longer sells Arbor Axle replacement parts... The Table Saw Arbor axle and Bearing Housing cannot use sealed bearings unless the saw case is re-milled and extensively modified. There are 2 Oil Hole Plugs (part# 475-32) that need to be opened and oil applied so the Arbor axle shaft does not get scored or worn.

I use 30wt motor oil to relube the Arbor Axle Shaft depending on amount of use, temperature, and axle rotation stiffness.

Remember, the higher the RPM speed of the table saw motor and/or the longer the use, the more frequently you may need to relube the Arbor Axle Bearing!


Nov 19, 2009 | Sears Saws

1 Answer

Looking for user manual Rockwell Model 215

hey there i just bought a used 215 7-
1/4" saw it came w/ a manuel
maybe i could copy it for u and send it to you

May 16, 2009 | Saws

1 Answer

I have lost my manual and need to replace the blade on a Delta 10'' power miter saw. The blade continues to turn as I try to loosen the nut and I do not know how to secure it. I know this is a dumb...

Many of the old saws don't have an arbor lock. If yours does, it would appear as a button or lever on the motor housing, sometimes underneath, sometimes between the blade and the motor/handle assembly. If you have such a lock, use it. It keeps the blade from spinning.
If not:
First off, unplug the saw.
Then look on the inboard side of the blade and see if the collet washer or arbor has facets for a wrench to grab it. Some older saws had these. If so, you can use one wrench to hold the arbor from turning and another to break the blade nut loose.
If not, lock the blade in the down position or hold it down against the base, and carefully jam a block of soft wood (like a hunk of 1 x 4 ) between the teeth of the blade and the table. You ought to be able to exert enough pressure to hold the blade from turning while you loosen the nut. (You''ll have to have the wood in the right position either fore/aft of the blade to keep it from turning). Once it's loose, you can hold it by hand and spin the nut off.
Reverse process to tighten.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take a moment to kindly rate this post....thanks!

Apr 10, 2009 | Saws

3 Answers

Delta 36-075 miter saw. Motor ok, but blade will not spin

It sounds as though one or both of the items are stripped. They mesh to drive the blade so I would not take a chance on just replacing just one. Also when you look at this you might also want to look at replacing the bearings and brushes. Make sure you clean out the gear housing or you will have immediate problems again. Also check where you buy these parts for their recommendation on the grease that needs to be used.

Mar 14, 2009 | Delta Saws

1 Answer

Changed delta saw blade

it turns the other way, to the right!

Oct 18, 2008 | Saws

2 Answers

Zero clearence isert

I'm not sure why the instructions said to change the blade in order to cut the slot. I've made several of the zero clearance inserts (for different blades) and always made the slot with the blade I intend to use it with. Of course, you need to match the inserts to the blades (I just tie wrap them together.

Aug 05, 2008 | Dewalt DW746X 10" woodworker's table saw...

Not finding what you are looking for?
Saws Logo

Related Topics:

395 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saws Experts

Tom Chichester

Level 3 Expert

26149 Answers


Level 3 Expert

63661 Answers

ray gallant

Level 3 Expert

37643 Answers

Are you a Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides