Question about Projection Televisions

Open Question

I have a orion tv and i can not tune the channels in and in the menu there is no where i can see where to tune in

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my jvc tv model hd-61g787 I cannot program channels


you can program channel either in the remote control or in the tv button panel. press menu then go to manual fine tune so you can program the channel one by one. you can use the volume up/down button to tuned the desired channel. to select channel use the channel up/down button.

Jun 01, 2013 | Projection Televisions

1 Answer

I just set it up (it is used) and I can't get to the "Channel Manager" in the setup menu, as it is grayed out. I can't auto program because of my inability to access this menu function.


Hi,
Channel menu will be grayed out if tv is set on AV Input, select TV source by remote or press any channel number to set tv on tv source, this will enable channel manager/ menu to tune channels in tv.
Hope these info will help you.
Thanks

Nov 25, 2010 | Hitachi 51F59 51" HDTV Projection...

3 Answers

I just got cable hooked up and I'm trying to watch tv on an older Orion tv/vhs. When I go to menu options I can go to all of them except the channel set. I know the cable connection works because I hooked...


Try switching between Cable and TV on your menu. Or you can insert a VSH and when you eject it, you should be able to bring up menu and do a reset.
Make sure the cables into and out from are in the correct positions, as a cable signal go to the output will not work.
I'm sure you have checked the connections in and out but just needed to make sure !
Do you have a remote for the Orion, without the remote, you may not have the correct functions available to function properly.

Oct 10, 2009 | Projection Televisions

1 Answer

Cannot tune in programmes I go to menu which brings up screen picture, audio, time but skips on tuning into progs and goes to options. Please help.


Hi,
Select TV as input source by TV remote or push Channel button on remote then go to TV Menu. That will enable Tuning menu in TV.

Jul 28, 2009 | Projection Televisions

1 Answer

I can not get the chanell to change on my Orion 27"2002 T.V. I can only change chanell from Video/ch4 and video2. I have Oneforall remote as also Jensen surf series. Can not find remote codes for...


Hello, I haven't found the codes for either remote. I did manage to find the menu after combining the volume buttons together. I have got the channel's to work by going to the menu and adding the channel's.

Apr 17, 2009 | Projection Televisions

1 Answer

Programming Channels


Your TV is likely set for "AIR" tuning rather than "CABLE" mode. In this case channels above 13 don't tune correctly. The tuning mode is adjusted through the setup menu (it's been too long since I've seen one of these to remember exactly how the menu looks). Once you set the tuning mode for cable, all the available channels should come in properly.

But you've said you have satellite, so you should have a satellite receiver connected to your TV, and you'd be changing channels there rather than on the TV. Your TV would be staying on channel 3 or 4 (if using the satellite antenna output connection), or on the A/V input you have the satellite connected to (if using the direct A/V outputs). Am I missing something about your system?

Feb 18, 2009 | Mitsubishi WS-73905 73" Rear Projection...

1 Answer

Hitachi T.V. remote CLU3842WL will not change channels.


There are two possibilities: either the channel memory has been lost due to the TV being unplugged for an extended period or the digital tuning system has a defective component. First thing to do is go into the TVs menu system and try to re-scan the channels. You may find that you can change channels after doing this. If its still not changing channel, the digital tuning board will have to replaced.

michtech

Feb 15, 2009 | Hitachi Projection Televisions

1 Answer

Samsung tv problem


Hi.

You havent listed your TV model but most Samsung sets that are digital will have A button on the remote marked DTV this will tell set to look at the digital chans.
Now try & go in to the menu & select tuning & scan the digital chans in.
One other thing are you in an area of the UK that can pick up digital channels without changing your aerial.

http://dysonmanuals.llc.nu/

Chris..

Mar 07, 2008 | Projection Televisions

2 Answers

Grundig colour tv lost digital channels


I'm sorry, but I have not worked with Grundig TV's, radios yes, TV's no. However, The menu shouldn't be hidden. The first thing I would try would be to UNPLUG the set from the wall, wait about a minute and plug it in again. This action should reboot the micro processor. On some sets, there are two levels of menus, main and advanced. You would want "channel setup" and /or channel scan. You may also look in the back of the manual and see if it list some service dealers that you could call for help. I hope this helps.
Electrode

Mar 03, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...