Question about Miller DYNASTY 350 TIG WELDER w/TIG TORCH 951074

1 Answer

I have a miller dynasty inverter tig welder   It has a help code that comes on when I turn it on the code is p-2

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 169 Answers

From the user manual for a generic dynasty model welder:
2 Help 2 Display
Indicates an open in the thermal protection
circuitry located on the left side of the unit.
Contact a Factory Authorized Service
Agent if this display is shown.

So you could have anything from a broken or disconnected wire to a bad thermal switch.

You can get user manuals specific to your welder at www.millerwelds.com

Rank this answer please,
Carl

Posted on Dec 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a Miller Dynasty 300 that won't tig weld, displays HELP 12 code. Suggestions??


Some welders have a resistor that is obvious and accessible but to give an error code it is likely something else inside. You'll have to look at the circuit board for a component that is burned. If you are lucky you will find a fuse.

Nov 21, 2013 | Miller SYNCROWAVE 250 DX TIG RUNNER WELDER...

1 Answer

Plugged in Miller Dynasty 350 and it said REL RMT. Wouldn't let me change the settings, all I could do is turn it on and off. I checked the owners manual inside and out and couldn't find...


Hi:
Legend REL RMT means release remote, this happens when your torch's trigger is depressed and you need to release the trigger to continue.
Check the owner's manual on section 7-4 troubleshooting, it's there.

Sep 08, 2011 | Miller DYNASTY 350 TIG WELDER w/TIG TORCH...

1 Answer

I have a help 12 code on my little dynasty machine, and no manual to tell me what it means, is this a major problem with my machine


On this page enter your serial number and you will be able to download your manual http://www.millerwelds.com/service/ownersmanuals.php In the Dynasty 350 manual I see no "Help 12", there is a 32 and 22. If the Help 12 is only displayed when you push a button, it is saying the combination you have selected is not valid.

Dec 22, 2010 | Miller DYNASTY 350 TIG WELDER w/TIG TORCH...

1 Answer

Help code 24 ?


On this page enter your serial number and you will be able to download your manualhttp://www.millerwelds.com/service/ownersmanuals.php In the Dynasty 350 manual On Page 76, section 7-4 it says: Help 24 Display Indicates a power supply to the control and interface board PC6 failure. Possible cause is a short in Pin A or Pin B of the remote control. Unplug the remote control and see if it goes away.

Dec 05, 2010 | Miller DYNASTY 350 TIG WELDER w/TIG TORCH...

2 Answers

Fan is always running wether welding or not.


Have you turned it off and try blowing compressed air on the cooling fins?

Jan 19, 2010 | Miller DYNASTY 350 TIG WELDER w/TIG TORCH...

1 Answer

Changing from 480v 3 phase to 220v single phase need diagram on a Miller Dynasty DX tig welder Serial # KH577649 stock 903519-01-1


i have a old miller thunderbolt CC*AC/DC welder its wire single phase 480 can it be switched to 220 single phase

Dec 02, 2009 | Miller Welding Tools

1 Answer

Hi, starts to weld fine after a few seconds hi


It sounds like you need to change out your SCR chip on your motherboard; Miller makes one that i have installed on all our 350xl's, I don't have the number on hand but i can get it for you tomorrow.

Oct 20, 2009 | Welding Tools

1 Answer

I NEED TO AIR ARC CAN THIS MACHINE DO THIS AND HOW


hook up to the stick position on the machine - to work + to the stinger hook stinger to the air arc hook up air to the air arc turn welder up to top {350}turn air on at the push button on the air arc & get busy

Apr 09, 2009 | Miller DYNASTY 350 TIG WELDER w/TIG TORCH...

Not finding what you are looking for?
Miller DYNASTY 350 TIG WELDER w/TIG TORCH 951074 Logo

591 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miller Welding Tools Experts

John Trevino

Level 3 Expert

1378 Answers

wadingriver
wadingriver

Level 3 Expert

2044 Answers

Jose Velazquez
Jose Velazquez

Level 2 Expert

227 Answers

Are you a Miller Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...