Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

1 Answer

How to replace the gear case for whirlpool washer lsn1000kq0

Need instructions on how to replace this part.

Posted by on

  • Anonymous Dec 20, 2008

    does the agitator need to be removed also

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,028 Answers

Remove 2 screws on rear of console lift console forward and roll back remove the lid switch connector remove the 2 clips on each side pull rear of cabinet forwardand slide cabinet off remove screws in center of agitator under cap and pull off ..lean washer backward remove pump clips and hoses remove 2 screws in motor clamps remove clamps and motor remove 3 1/2 in bolts holding gearcase to bottom slide gearcase out remove clutch and reinstall on new gearcase if you go slow and take note reassembly not that hard

Posted on Nov 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gearcase


No gear case, I'm assuming your washer sounds like a freight train? Need more info about your washer.

Apr 30, 2014 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool Washer model # LSN1000KQ0 overfilling


did you plug the hose back into the water level switch, double check to see if it is plugged, if it is your water level switch might be defective. trouble shoot by taking the front panel off... turn on the washer by using the timer, set water level to small...on the bottom of the tub housing there should be a nipple where the clear hose connects onto.....follow the clear hose from the switch down to the bottom of the tub.........disconnect the clear hose on the bottom of the tub.....plugg the nipple with your finger.........gently blow into the hose with your mouth.......but make sure the water level in the tub is at least at half way full...and the washer is on and filling up with water ...after you blow into the hose the washer should agitate.......if it does agitate your water level switch is defective...connect hose back........get your model number and source for the switch.........

Apr 10, 2010 | Whirlpool Washing Machines

1 Answer

Whirlpool washing machine clutch replacement


Hi

Thanks for using FixYa. For servicing the clutch you’ll need to first remove the gear case. The gear case can be removed by first removing the outer cabinet. After removing the cabinet, remove the pump and motor assembly. Now carefully lay down the washer on its back and remove the 3 bolts securing the gear case. Now pull the gear case straight out from the tube support assembly. Now, compress the clutch spring with a pair of pliers and lift the lining from the clutch hub. To remove entire clutch assembly begin by removing the spin tube thrust washer up & off the agitator and then remove the tube support ring. Remove the retainer ring and lift the clutch hub up and off spin pinion.


Please do rate the solution and revert for further assistance.

Thanks

Rylee

Nov 25, 2009 | Whirlpool Washing Machines

3 Answers

WHIRLPOOL WTW6400SW1 WASHER HAS A LOUD BEARING NOISE DURING SPIN CYCLE


The washer has 2 standard metric bearings, a 6005 and a 6006. Its a couple hours worth of work to disassemble the entire washer and replace them

Jul 20, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

My washer will wash clothes and it drained, but will not spin makes a loud roaring noise what is wrong?


OK, that roaring is coming from a damaged direct drive assembly. the gear box is damaged. you will need to replace asap.

Gear case housing kit with main drive gear will run you about a $190.00


Jun 03, 2009 | Whirlpool LSR5132PQ Top Load Washer

1 Answer

Whirlpool Washer Model:LSN1000KQ0,SER: CM4267948, Type: 111 - Need nylon gear in transmission gearbox.


From the information provided, it sounds like you need WPL 285362 (gear and pinion kit) which you can find at appliancehelp.com for $59.95. You can type in your washer model and see the diagram of each part before ordering so you get exactly what you need.

Apr 16, 2009 | Whirlpool Clothes Washer Timer Knob -...

1 Answer

Whirlpool gear case won't come out


did you take the agitator out of the washer it has a bolt that holds the agitator to the gearcase. if you did sometimes you have to take a screwdriver and tap the shaft of the gearcase from inside the tub

Dec 20, 2008 | Whirlpool GSC9455 Top Load Washer

1 Answer

LSN1000KQ0


by chance if you removed the drain hose on the machine when you replaced the direct driv coupling, did you insert the drain hose back in too far, it only needs to be inserted into the drain about 4 inches and should not be sealed air tight
if it is inserted too far it will siphon out the water untill the pressure switch calls for it to fill back up over and over

check the drain hose and let me know if you need any more help

Jun 23, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

My washer has a ticking noise now it wont wash


most the time on kenmore whirlpool the noise is the basket drive and gear case needs replaced some time you can replace basket drive fix it and 90% time all it is depends on clicking noise is the coupling between motor and gear case bad if you have rubber pieses on floor ubder it thats all it is very cheap to repair

Feb 27, 2008 | Washing Machines

1 Answer

Oil on floor underneath washer


jeffnew The oil which you see on the floor is coming from the gear case. The gear case is not repairable and it has to be replaced. If your washer is less than 1 year old do not wait and call Whirlpool - it is under full warranty. If your washer is between 1 to 5 years old, then the part is still under limited manufacturer warranty but you are liable for any trip and labor charges. It could be much over $200.00. If you are handy and willing to save money, you can buy the part for less than $150.00 and replace it yourself. In that case, I can find the best deal for you and help you with step by step instructions. Gendos...post back

Feb 09, 2007 | Whirlpool Ultimate Care II LSQ9564J Top...

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

805 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

prem mathew

Level 3 Expert

662 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...