Question about Panasonic PT-45LC12 45" Rear Projection HDTV-Ready Television

1 Answer

Treadmill speed problems

I have a trimline 3600.1 treadmill and the peed will not adjust. It goes from stop to fast with no slow spped available. I checked the speed sensor and it is 1/4 inch from magnet. I tried to calibrtae the spped but it won't aloow me to adjust to .5. can you help?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 4 Answers

Http://webpages.charter.net/chestnuts/Trimline%20Owner%27s%20Manual-1600-2600-3600-4600.pdf

Posted on Jan 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hdr505 slow


either a problem with the unit's power supply--look for puffed up caps on top--see photo of bad ones .

Or some microprocessor problem in the unit.
4_2_2012_10_53_44_pm.jpg

Mar 31, 2012 | Projection Televisions

1 Answer

I was given a set of DVDs. Most of them play for a while and then stop then screen goes black and returns to PLAY. I fast forward to past the stopped area and it plays again for a while then stops again...


there is a compatibility problem here, there are small difference's that cause this problem it is due to the way the information is encoded on the disk, the there are some players like PHILLIPS that will play anything, others like COBY are very finicky, my best suggestion is buy or borrow another player.

Feb 10, 2010 | Projection Televisions

1 Answer

The picture on my TS-4573 rear projection tv has started to roll vertically at a fast rate. How can I make this stop. On old tv's there was a vertical hold adjustment on the back that you could play with...


this fault is caused by defective electrolytic capacitors in the vertical deflection circuits, they need to be changed out, do this before it causes more problems, there are no adjustments for this anymore.

Jan 30, 2010 | Projection Televisions

1 Answer

Rolling green horizontal bar from top to bottom,then bottom to top and so on. sometimes rolling fast,sometimes slow and sometimes the green bar stops in the middle of the screen.every once in a while the...


This TV needs a service adjustment done. Looks like a vertical or horizontal IC is failing. I'd go ahead, and shut off until services adjustment is made. Have you unplugged for a few minutes and plugged back in? However, I'd have a service tech look at it.

Oct 25, 2009 | Mitsubishi WS-48513 48" Rear Projection...

1 Answer

The screen on my jvc av-48wp30 is lower on right side than left. is there any way to adjust this?


peed make that adjustment with the yoke or by the internal parameters of the tv but I suggest you check it to be a failure because oued and capacitor

Aug 22, 2009 | Projection Televisions

1 Answer

A mouse got into the bottom and peed on the cercuit board and tv wont work casn it be fixed?


Probably can be fixed but will be exspensive. They may have to replace circuit board the mouse peed on. They should make those tv's mouse proof so customers dont have to pay these expensive repair bills or buy new tv every two years. Smaller holes and vents. If the television is pretty new see if it is under warranty. Good luck.

Aug 12, 2009 | Hitachi Projection Televisions

1 Answer

I have a KP-65WV700 and the screen looks a lil to green


OK, I'm the guy that was having the same problem, but had a blue tint to the screen. I also had blue lines running across the screen, and when I followed the steps below that were posted by another user not only did the lines disappear, but the blue haze vanished as well. My tv looks like it's new again, so you may want to try this:

noavatar_s.gif Guest
Rank:nonexpert_s.gif Apprentice
Rating: 0%, 0 votes
I have fixed this several times on my KP 65WV700

As Slinteriors posted if it is a thin curved line you need to adjust the screen control, it's sorta like a brightness for each color, and if one color is too high it will produce a thin curved line.

The best way I have found to get to the controls is by removing the lower grey speaker cover front the front of the TV. There are 6 screws if i remember, 3 on each side. Then it snaps off, seems like its going to break but you have to pop it off pretty good.

Once its loose you have to remove a cardboard like cover plate in the center that will give you access to the small controller board.

Now be very careful while experimenting on which knob controls which colors. Turn them very slow, if you turn to fast you will cause your TV to shut down. If this happens, turn the adjustment back to original spot and turn TV back on and take it slow.

Adjust the correct color until the line just goes away. Its easiest to do this with a black screen.

Nov 18, 2008 | Sony KP-65WV700 65" Rear Projection HDTV

2 Answers

Won't come on


hy i got a toshiba 42" LCD tv ,when i press the power boton
iget the red light,& it stay that way ontil i pressthe power back off
thanks for any help

Jun 26, 2008 | Toshiba 62HM95 62" HDTV

3 Answers

Sony kp-65wv700


I followed GuestUser/ Slinteriors advice and I fixed it. Open the front of the TV and there are 6 little nobs in the front. The botton 3 are what you need to adjust. from left to right the color controls are BLUE, RED GREEN. For the blue lines, slightly (I really mean very slightly) turn the botton left nob clockwise (right).

Mar 21, 2008 | Sony KP-65WV700 65" Rear Projection HDTV

Not finding what you are looking for?
Panasonic PT-45LC12 45" Rear Projection HDTV-Ready Television Logo

476 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

Josh Whitehead
Josh Whitehead

Level 3 Expert

1146 Answers

The Knight
The Knight

Level 3 Expert

68301 Answers

Are you a Panasonic Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...