Question about Projection Televisions

1 Answer

My Philips 17' LCD flat TV don't display any picture or sound but keep flashing a red led.This Led is solid green before the problem.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 106 Answers

Possible capacitors on the power supply board. Depending on the age of the unit, parts may or may not be available

Posted on Nov 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

No sound or picture. red timer light on. wd60735


Hi there,

This model as 3 LED indicator lights:

1) Power/Timer 2) Status 3) Lamp


If "STATUS" LED is blinking RED:

1) Internal Fan has stopped. These tv's require fans, to prevent overheating and causing damage.

If "STATUS" LED is solid RED:


1) Circuit failure (short)
2) Disconnected DVI cable, chassis to engine
3) No LAMP-EN signal from Engine to turn the lamp On.
4) Ballast UART communication problem.

If "LAMP" LED is solid RED:

1) Lamp Failure - Lamp failed to turn On.
2) Lamp is broken (e.g. burst or blown)
3) Lamp turns Off during P-ON

There is no data relating to TIMER LED being solid RED.

Hope this helps.

Cheers,

Scott

Feb 01, 2013 | Mitsubishi Projection Televisions

1 Answer

Installed new lamp. When powered up blue solid light and yellow blinking light (15x) , tv would torn off and on several times trying to light lamp. Once that failed red blinking light and yellow solid...


Hi Genaro,

Blue led light lit solid and yellow led light flashes is an initial attempt of the set to re-light the lamp.Red led flashes and yellow led light solid means that the lamp won't light up that's why it only has sound without the picture.
Since you've replaced the lamp twice and still the symptoms persist, I suspected that the fault came from the ballast board and not on the lamp itself. If the ballast board gone to malfunction, there's no high voltage will produce to light up the lamp and will sensed by the processor and trigger the error code (Flashes/solid led light with color code).

To verify whether the ballast board is faulty or not, check if the lamp will lit by looking through the lamp door louvers at the rear of the cabinet upon turning on the set.
Please let me know what you will find to assist you further.

Jdvillanueva

Nov 05, 2011 | Toshiba 65HM167 65" Projection Television

1 Answer

Toshiba 62 inch dlp tv keeps flashing green and will not turn on


green flashing for .3 sec with solid red indicates lamp problem. and do you have the manual? If so, look in the appendix for a section 'LED indications'. that gives you the code for the indications.
Good luck..

Aug 29, 2011 | Toshiba 62HM195 62" HDTV

1 Answer

When turned on green light flashes and no picture


Check the Lamp if no picture, audio may be present. Screen is completely dark. Lamp LED flashes 2X every 5 seconds, Power LED flashes GREEN for 140 seconds then flashes RED.
Check the ballast if no picture, audio may be present. Screen is completely dark. Lamp LED flashes 3X every 5 seconds, Power LED flashes GREEN for 140 seconds then flashes RED.

Dec 24, 2009 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

I have a philips dlp 55pl9773 has one red flashing led on the front when i do a hard reset tv boots up lamps lites led goes from flashing yellow to green for about ten seconds and then back to red flashing...


MY philips tv model number 55PL9773/17 WAS TURNING OFF THE SCREEN AND LEAVING THE AUDIO ON FOR ONE MINUTE. THEN THE YELLOW LIGHT STAYED ON. THEN THE LIGHT TURNED OFF. thEN I TURNED ON WITH THE REMOTE AND THE YELLOW LIGHT TURNED ON AND A FEW SECONDS LATER CHANGED TO THE GREEN LIGHT AND THE TV TURNED ON. AFTER A FEW MINUTES, BETWEEN 10 AND 30 IT DID THE SAME THING. NOW IT IS OFF WITH A BLINKING RED LIGHT PERMANENTLY ON. TO TURN IT OFF I HAVE TO UNPLUG IT FROM THE WALL. I REPLACE THE LAMP A FEW WEEKS AGO AND IT IS FINE.

Dec 01, 2009 | Philips 55PL9773 55" Rear Projection...

1 Answer

My philips 50p8341 beeps then flashes the red led 4 times


4 Blinks means that an incorrect voltage had been detected on the +5V circuit coming from PSU to digital control board.
The PSU must be tested and eventually repaired or replaced.

Aug 08, 2009 | Philips Projection Televisions

1 Answer

I have a Sony Bravia KDL-46S2530 50 inch the problem is when powering the TV from off the green LED comes on and then you get a moment of display like TV channel display, then you get sound with no...


In your case the led flashing is indicating protection mode. That usually indicates an internal fault.

Follow the full troubleshooting below:

If an LCD TV has sound but no picture do the following:

Use the source button to ensure that source is not set to the wrong input.

Try unplugging power cord for ten minutes, to ensure it is not a setting problem.

Check all the video cables at the back of TV.

Check Light /Color settings.

If problem persist and does not depend on external receiver or settings, then it is likely an internal fault.

If it has sound but no picture then one of the following parts is faulty, and must be tested and replaced:

The inverter is the high voltage board that provides variable power to the backlight lamp. This is the most common. When inverter is faulty you can get no picture, or a very dim picture that can only be seen by pointing a torch light with a 45 degree angle on the LCD surface from very near distance.
The inverter must be tested by reading voltages with a multimeter.

The LCD ribbon cable/LCD display and connectors.
This is quite uncommon, but happens. If the TV had been hit or moved the LCD cable may have slipped out, or the LCD connector may be damaged.

The LCD controller board.
This is the board that controls the video signal, it is difficult to test, as there is need to read determined values on IC pins. To test this board you need to purchase a service manual and follow the troubleshooting diagrams on service manual.

Input/Output Signal boards.
This are the boards where you connect the video and audio cables, if a signal board is defective, then you may get no picture on particular inputs located on faulty board.

If under warranty contact the manufacturer ringing the number on the user manual.

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |

May 03, 2009 | Projection Televisions

2 Answers

Sony 46" rear projection LCD HD - picture and sound go on and off


personally i would call a tv repairman out to fix the set.you can get alot of different opinions on here about what it may or may not be but the best thing to do is call a repaiman and let them fix it

Jan 27, 2009 | Sony KP-46WT500 46" Rear Projection...

1 Answer

Philips 42fw3090/17 don't turn on, only LED comes on red


first thing i would do is take the lamp out and look at it, it dhould be on the left side of the tv, you will see a little door at the bottom

Jan 10, 2009 | Philips Projection Televisions

Not finding what you are looking for?

Open Questions:

Projection Televisions Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...