Question about Washing Machines

1 Answer

Will not complete wash, stops about 5mins after starting

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 111 Answers

Does it work again after several hours? If so, the motor is overheating. It has a cutoff circuit breaker inside. It cuts off when it gets hot. But the problem is, something is making it work hard and it gets hot. Maybe the pump is stuck or something.

Posted on Nov 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Indesit IWD7145K Washing Machine Error code F06 flashing on digital display + all program indicator lights. What does this mean. There is no such error code in the troubleshooting section of the manua


F06 - Door lock fault
Issue: Washing machine door cannot be opened or closed/when the door is closed the machine the programme will not start.
Advice: If your washing machine door will not close, please check for any obstructions in the door lock.
OR,
Switch off the device. Disconnect power. Wait about 3 minutes.
Open the door, then close. Reconnect device to the network.
Start device.

Cause: Door lock fails to close / open door lock triac open / closed,
frequency signal fault

Dado

Feb 12, 2015 | Indesit Washing Machines

1 Answer

Zoomerpup stopped working


Try removing the battery ONLY for about 5mins. Then reinsert the battery and see if it powers on.
If that fails, remove the battery AND Media Card for 5mins. Reinsert battery first...power on. Then SD card.
If neither of those work, check charger to see if it is working. If there is an LED light on the actual charger, this should light up. If there isn't, then the charger should at least be warm after say, 30mins of charging. If it is still cold, you may need to replace the charger.

Nov 25, 2013 | Toys

1 Answer

My cda washing machine keeps flashing up code FO4 and it is failing to start can you help?


Do not know your model number but give this a try .erase the flashing LED . hold the start button in for 2 seconds this should reset the machine . unplug from wall wait 5mins and try again .

Feb 22, 2010 | Washing Machines

2 Answers

NORMAL Wash light is blinking and I can't CANCEL wash. GE Quiet Power II PROFILE dishwasher. Started a normal wash and a few minutes into it the NORMAL light started blinking and can't find a way to reset.


We had the same issue with ours...tried turning off at the breaker, still didn't reset. Contacted appliance repair who came in and unplugged it from underneath the sink, waited a few seconds and plugged it back...dishwasher reset and repairman charged trip charge and labor $65 BUT problem is resolved and we now know what to do in the future.

Jun 09, 2009 | GE Dishwashers

1 Answer

Kitchen aide front loader washing machine won't finish cycle


On ours, i think that those codes were overload codes.. i had to go downstairs and turn the circuit breaker right off for about 5mins - when i clicked it back on, the washer reset.. i took some of the extra wet towels out and ran another wash with no issues..

good luck
tpug

Apr 27, 2009 | KitchenAid KHWS01PWH Global Horizontal...

1 Answer

Cuts out after 5mins


Hi Dave. The chances are that the thermal protect device is faulty or the carbon brushes are on there way out.

Jul 22, 2007 | Dyson DC07 Bagless Upright Cyclonic Vacuum

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

64034 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...