Question about Philips DECT/VOIP Phone System

1 Answer

I cant register my phillips voip43315/05

The phone was registered and in use but after a power cut there are no tones and a message saying UNREGISTERED

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My phone is saying unregistered

Posted on Aug 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Uniden D3098S I have 2 register hand sets #1 and #2 I have a 3rd one having trouble registerting it to the base iam 2 feet away from the base unit it says check base power & out of range


Registering a Handset


If you see a "not registered" message on a handset, you must register it to a base before using it.

1. On the base, open the menu and select "Register Handset"

2. On the handset, press and hold POUND (#) until the handset display says "Handset Registering" (about 2 seconds).

3. Wait until the handset display says "Registration Complete" (about 30 seconds), then pick up the handset and press eND/CleaR.

# If you don't hear a dial tone or the display says "Registration Failed" charge the battery completely, then try again.

May 12, 2016 | Uniden Phones

1 Answer

How do you register a old uniden SSE27 handset to a new Uniden SSE37 base


The following is taken directly from the SSE37 owners' manual:

Registering a handset
If you see a "not registered" message on a handset,
you must register it to a base before using it.
1.
On the base, open the menu and select
Register Accy.
2.
On the handset, press and hold #/DND
until the handset display says
Handset Registering (about 2 seconds).
3.
Wait until the handset display says
Registration Complete (about 30 seconds),
then pick up the handset.
If you don't hear a dial tone or the display says
Registration Failed, charge the battery completely,
then try again.


Good luck!

Feb 19, 2015 | Uniden Phones

1 Answer

I cant dial out it says register HS i am not familiar with the procedure.


When you reset a handset (or if you buy a new one1, that handset displays a Handset Not Registered message. If you see this message on a handset, you need to register it to a base before you can use it.
Registering a handset
Does the handset fit in the base cradle?
Yes
No
Place the handset in the base.
The display should say Handset Registering.
1. On the base, open the menu and select Register Handset. The display should say Handset Registering.
2. On the handset you want to register, press and hold # until the handset display says Handset Registering (about 2 seconds).
In about 30 seconds, the handset display should say Registration Complete. Press TALK ( )/FLASh and make sure you get a dial tone. page29image32024
27
If...
Try...
- you don't hear a dial tone- the display says Registration Failed
Making sure the handset is fully charged, then start over at step 1.
To register a handset to a different base, see the section "Expanding Your phone" in the user's guide for the other base.

Mar 18, 2014 | Uniden DECT 6.0 Cordless Phone ID

2 Answers

Cannot clear message on handset that says I have a voice message.


I resolved the problem but I'm not 100% sure of how I did it. If it happens again I'll try it again. I left the answering machine OFF so the Voice Mail would take any messages. A friend phoned and left a message in the VOICE MAIL, I knew this because of the broken dial tone when I went to make a call. When I erased his message the 'New Voice Message' displayed on the handset disappeared. I figure a previous caller hung up just after the voice mail picked up. It was not long enough so it did not register in the voice mail but somehow registered on the GE phone. Since there wasn't anything registered in the VOICE MAIL to erase the message was 'stuck' on the handset display. As soon as there was a message registered in the VOICE MAIL that could be erased it also cleared the message on the handset.

As i mentioned, if it happens again I'll try it to see if it works, until then I am not going to tempt fate.

Dec 24, 2009 | Uniden Cordless Phone

2 Answers

Base station and units all say 'searching'


You may need to register your handset to the base.
Normally ,there is a advanced setting ,register handset. At the same time, press and hold "page" key on your base 4 to 5 second , there is be a registation success tone from handset. You can register all of your handset ,one by one. Some model need to input register code, normally ,it is 1234 , or 0000.

Dec 22, 2008 | Philips DECT 2252S Cordless Phone

1 Answer

Phillips SE140 duo - had power cut now phone not registering with base! I dont have the manual anymore!


you may have to input you country code again as you did at set up .then you will probably find that your handset will register as long as you use the master charger

Dec 18, 2008 | Philips Phones

2 Answers

STILL SAYS "PLEASE REGISTER"


I think this may be the answer. With multiple handsets reading "Please register" and a "working" base station (w ith dial tone). If you bring the remote units to the base station and place them on hte base, they will register and stay registered after you return them to the remote base. It doesn't say this anywhere in the instructions as it gives you the impression the remotes will register from their own base.

Jan 04, 2008 | GE 25932 Cordless Phone

2 Answers

Have ONE phone - ONE base station - still says "PLEASE REGISTER"


With the 6.0 gig set, the phones in the box are already registered. The manual tells us how to de-register and register. You might want to consult that part of the manual.

Dec 29, 2007 | GE 25932 Cordless Phone

Not finding what you are looking for?
Philips DECT/VOIP Phone System Logo

Related Topics:

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Phones Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

kakima

Level 3 Expert

96683 Answers

Are you a Philips Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...