Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

1 Answer

Not draining or spinning

My washer fills with water no movement when in wash cycle and when done clothes are still soaking wet

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 306 Answers

There is a coupling in between the motor and transmision cost about 10 bucks if that much. Sounds like you need a new one. Flip washer on it side and look at the motor where it connects to the transmission you will see a coupling.

Posted on Nov 26, 2008

2 Suggested Answers

  • 714 Answers

SOURCE: clothes are soaking wet after washer is done

maybe your clutch is slipping not getting full spin speed,,,,or could be a problem with your basket drive assy

Posted on Feb 21, 2010

Testimonial: "thought it might be something simple like changing out a switch. Looks like we need a tech house call. Thanks"

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ge washing machine fills up with water on spin cycle


Sounds like the timer is screwed... Sending out the wrong signals and the dryer is doing the rinse cycle when it should just be the spin cycle. Do t know what your timer looks like in that washer but most now days look like the picture. 11_11_2013_2_52_52_am.png

Aug 16, 2013 | Washing Machines

1 Answer

Clothes are soaking wet after washer is done


maybe your clutch is slipping not getting full spin speed,,,,or could be a problem with your basket drive assy

Feb 21, 2010 | Whirlpool LSB6200KQ Top Load Washer

1 Answer

Clothes soaking wet after washer is done


There is either a problem with the drain or spin cycle. Before the spin cycly starts, ensure that the water drains fully. If it does, then it may either be the belt slipping or the timer malfunctioning. If there is water in the tub when it starts spinning, then you have a blockage in the drain line.

Feb 11, 2010 | Whirlpool Washing Machines

1 Answer

Washer drains then spins then fills again and drains but no spin


Try this, unplug washer for two minutes, plug back in, open and close lid seven times slowly, this will reset the computer and the electronic motor. Also on water level switch, make sure hose from switch to tub is not plugged, blow it out, gets clogged with soap.

Sep 09, 2009 | GE WBSR3140DW Top Load Washer

1 Answer

LG front load washer/ clothes still wet after final spin


The heavy jacket prevented the washer from spinning at a rapid pace, so I added a heavy bathrobe to absorb some of the water and to balance the load. The washer then spun very quickly and drained out all the water.

Jan 07, 2009 | LG WM-1832C Front Load Washer

1 Answer

Clothes are soaking wet after the entire wash cycle.


The motor controller is likely bad - not getting to the HIGH spin.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 07, 2009 | Washing Machines

1 Answer

GE Top Load Washer WLSR2000G3WW~smells like burning and wont drain


The clothes are wet after spinning When the clothes are wet at the end of a cycle, check these:

Motor coupler
Spin cycle
Siphoning
Water-inlet valve
Motor coupler To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning:

  • If it's spinning when you lift the lid, the coupler is fine.


  • If it isn't spinning--and your machine was produced by Whirlpool®--you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely.


Spin cycle If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component.

Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician.

Siphoning If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess.

Water-inlet valve Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.

The cycle doesn't advance When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.


  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.

Nov 06, 2008 | GE WBSR3140DW Top Load Washer

1 Answer

Washer mah5500b


Replace the door Wax motor & main Control Board.

Apr 13, 2008 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

GE Front Loading Washing Machine seems to be holding water....


The high speed spin of a front load washer should normally do a good job of getting squeezing out the water but if there is an oversudsing condition that makes it hard for the drain pump to operate then the suds and water will just stay there. First make sure there is no actual clog in the drain line then run a load with no soap or detergent and see what happens. It's always better to use a low suds detergent with this type of machine

Mar 08, 2008 | GE WSXH208A Front Load Washer

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...