Question about Dishwashers

Open Question

Gateway Timeout The following error occurred: [code=DNS_TIMEOUT] A DNS lookup error occurred because the request timed out during the lookup. -------------------------------------------------------------------------------- Please contact the administrator.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bosch shx36l05uc/21: After running diagnostics the 'wash' button keeps flashing, can someone tell me what the problem is?


Hi Jeff, As you can see there's 3 different Bosh washing machine models, Hope you can find your error code.... CHEERS..

Bosch Washing Machine Fault Codes

F16 - Door lock error
F17 - Inlet valve error detected
F18 - Drain error detected
F23 - Anti flood device has been activated
F34 - Door lock error
F42 - Motor fault
F43 - Motor fault
F44 - Motor fault

Bosch WAE Range Washing Machine Fault Codes

F16 - Door lock problem
F17 - Inlet valve
F18 - Drain pump
F21 - Motor
F23 - Anti flood system activated

Bosch WFP Range Washing Machine Fault Codes

F01 - Water intake timeout
F02 - Heating timeout
F03 - Draining timeout
F04 - Motor fault
F05 - Uncontrolled motor startup
F06 - Short on NTC Detected on hot water intake
F07 - Open circuit NTC Open circuit wiring
F08 - Door open when program started
F09 - Unexpected heating
F10 - Communication error
F11 - Overheating
F12 - Short circuit
F13 - Mains voltage too high
F14 - Mains voltage too low
F15 - Faulty temperature sensor on motor PCB
F16 - Faulty rinse sensor Displayed only in test

Mar 30, 2016 | Bosch Dishwashers

1 Answer

What is err1 and err3 in elekta dishwasher?


Electra Dishwasher Error Codes and other critical errors can occur when your Windows operating system becomes corrupted. Opening programs will be slower and response times will lag. When you have multiple applications running, you may experience crashes and freezes. There can be numerous causes of this error including excessive startup entries, registry errors, hardware/RAM decline, fragmented files, unnecessary or redundant program installations and so on.follow the instruction on the link below to find your solution http://www.saetechnologies.com/electra-dishwasher-error-codes/

Mar 03, 2015 | Dishwashers

1 Answer

Indesit dishwasher error codes


Temperature timeout - Maximum time to reach temperature elapsed.

Dado

Aug 20, 2014 | Indesit Dishwashers

1 Answer

Why Ariston lbf51 washing and drying light rapid flash


AL03 - Drain Timeout (drain problems)
LED 1 (washing) and LED 2 (drying) flashing.

Probably the siphon of the apartment is clogged.
  • Remove the drain hose and make sure that is not clogged.
  • Drain water in a bucket.
  • If the dishwasher drains the water, clean the siphon of the apartment.

24501411-0h3kxpflbez5mdeb5anq3st4-5-0.jpg
Dado

May 25, 2014 | Ariston Technologies LL65 Built-in...

1 Answer

My indesit idl has stopped working. The red light comes on but none of the green setting lights come on - any ideas


Led 1= Prewash / 3hr
Led 2= Wash / 6hr
Led 3= Rinses / 9 hr
Led 4= Drying / 12hr

LED. illuminated
1 = Overflow ( water in base )
tip machine back. does water come out? if so you have a leak, possibly from bottom spray arm nut or loose salt pot. see if they are loose. if not, remove the base, put dishwasher on a block of wood, shine torch underneath to see where the leak is.

1+2 = Pump timeout, or Software recognition error ( timer not programmed, wrong keypad)

1+3 = Circulation pump not working

2+3 = Not filling

2+4 = Heating circuit not working

2 = Solenoid valve 'broken'

3 = Thermistor (NTC) cicuit not working

4 = Temp not reached whilst heating ( poss NTC detached from casing).

remove door panel. ntc is attatched to the rear of dispenser, a little white thing with 2 black wires on it. refit to the clip on the dispenser.

It is usually necessary to 'reset' the machine after a fault code has been displayed. Resetting.
Switch dishwasher OFF, rotate the selector switch to STOP/CHANGE and switch on, after a few seconds the LEDS will go out enabling a new programme to be selected

Aug 20, 2011 | Dishwashers

1 Answer

Not enough water is dispensed during fill cycle. This causes top washer not to have enough water volume to move top washer wand.


First check that the fill float switch is working.

Next that the fill valve doesn't have crud that limits water flow. They MAY have a timeout to prevent overfilling if fill is too slow and that could cause the priblem if fill valve is partially blocked.

Aug 10, 2009 | Kenmore Dishwashers

4 Answers

Bosch 24 in SHU66C05UC/14


WHAT IS WRONG WITH YOUR DISHWASHER?

small_9_26.jpg For a detailed Dishwasher illustration, click below.

redarrow.gif Built in
Warning!To avoid personal injury or even death, always disconnect yourappliance from its power source--that is, unplug it or break theconnection at the circuit breaker or fuse box--before you do anytroubleshooting or repair work on your appliance. Also, because somecomponents may have sharp edges, use caution while working on yourappliance.

There's an error code on the digital display

It doesn't work at all
It cleans poorly
There's no water entering the machine
The water doesn't drain from the machine
It's noisy
It leaks
The dry cycle has problems
The door has problems
The cycle doesn't complete
I see an error code
The detergent cup doesn't open
The cycle times are too long

Jul 08, 2008 | Bosch 24 in. SHU66C02 / SHU66C06 Built-in...

2 Answers

Blinking Green Light


Here's what I could find on the your error code:

A blinking clean light that flashes 7 times and cannot be reset, occurs when the electronic control does not detect a water temperature increase during the main wash. This could be an indication of a failed heating element, in line thermostat, electronic control board and/or wiring. This problem can also occur if the main wash pump becomes clogged and it not spraying sufficiently. I hope this helps you.

PS A faulty door latch can also cause this error code.

Jun 23, 2008 | Dishwashers

1 Answer

Clean light flashes 7 times


Here's what I could find on the your error code:

A blinking clean light that flashes 7 times and cannot be reset, occurs when the electronic control does not detect a water temperature increase during the main wash. This could be an indication of a failed heating element, in line thermostat, electronic control board and/or wiring. This problem can also occur if the main wash pump becomes clogged and it not spraying sufficiently. I hope this helps you.

PS A faulty door latch can also cause this error code.

NOTE: There should be a tech sheet located behind the lower panel under the door that lists all the fault codes and how to troubleshoot them. If you need further assistance, please let me know.

Jun 20, 2008 | Whirlpool 24 in. DU1050SS Built-in...

2 Answers

Error


It's probably the heater element that has gone, but it could be a simpler fault like the pressure switch not activating. See this video it should give you the general idea

Sep 03, 2007 | Hoover 24 in. HD98E Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

269 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

13732 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...