Question about Regal Ware K813BK La Machine Food Processor

2 Answers

Can't figure out how to turn on Regal LaMachine I food processor

Bought at garage sale without a manual. Not sure if unit is broken, or if I just can't figure out how to turn it on/pulse it. "button" looks ok, but won't turn or press, or anything. Any suggestions?

Thanks

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

It's very easy--but you have to know the trick--I know 'cause it took me awhile to figure it out. Place the machine with the on-off/pulse button on your left. Lock the container in place--the handle will be on your right. Put the blade on the shaft. This is the trick: Lock the lid in place so that the shoot is directly in front of you and the "***" slides into the **** on the left of the machine (between the container and the inside of the machine, left of the on-off button). Good luck!

Posted on Nov 30, 2008

  • BeaforB Nov 30, 2008

    I noticed that the verbiage I used was not acceptable--even tho it was a legitimate description! Let me rephrase: Lock the lid in place so that the shoot is directly in front of you and the rectangular piece that sticks out on the lid slides into the narrow horizontal opening on the left of the machine. (I hope this is clear!)

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

This is from the manual:
Place bowl over motor base and shaft by placing handle to the farthest left, near On-Off/Pulse switch. Twist it to the right (counterclock wise) until it locks into position. The slotted tabs on the side of the bowl bottom should slide over the projections on the base. When the handle is directly facing you and centered, the bowl is locked into position.

Posted on Jul 20, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cuisinart DLC-8S Food Processor: On/Off Switch not working


Replacement of the switch would be a likely repair unless other damage makes replacement impractical.

Apr 14, 2017 | Cuisinart DCC Food Processors

1 Answer

Bought a Moulinex 517 food processor at an estate sale. Do you have an instruction manual for this model?


I have an instruction manual for the moulinex 517. I bought mine in 1980. I am looking for the food pusher, which has been missing from mine for years. Does anyone have one of those?

Dec 01, 2009 | Food Processors

2 Answers

Just purchased Oster 3322 food processor and cannot get it to work. Have used various brands and know that this unit has been properly assembled. Neither the 'on' or 'pulse' buttons will activate the...


Oster is a good brand. Unplug it and try to turn thhe motor by han using an attachment. Or, tap the unit with a run button depredded. Here is why. Sometimes new brushes on a motor have a coating on the conrtact surface. It is vry thin and it is not permitting a good electrical contact. If you can't turn the motor, slap it a couple of times with it on. Once it starts, let it run for 2 or3 minutes and you troubles are over once the brushesseat and clean up. Good luck and remember to unplug when hands are on or near the attachments.

Oct 27, 2009 | Food Processors

1 Answer

I have a small Cuisinart food processor and I cannot figure out how to turn it on. It has two levers low and high. I have it plugged in and the lid on? Please help. Fiona Slattery 858-752-8591


Hi,

Your PowerBlend Duet™ comes with a food processor button. This button is the perfect speed for all your food processing tasks. Always use this speed when using the food processor. You may also use the Pulse button with this function for pulse-chopping.
To use your food processor, make sure that the bowl is assembled properly and the blade or slicing/shredding disc and the cover are locked into place.
When you use the control panel, the LED will light next to each button you press.
Press the On button. For continuous operation, press the Food Processor button. Motor will start if you have followed assembly instructions.
To turn motor off, press the Food Processor button again or the Off button.
For on/off operation, called pulse-chopping or pulsing, press the On button, press the Pulse button, and then press and release the
Food Processor button the desired number of times. Motor runs as long as you hold the Food Processor button down. The motor stops when you release control switch. Try it a few times.
You control the duration and frequency of pulses by the length of time you hold the Food Processor button down and the rate at which you press it. Pulses should be short bursts. Allow enough time between pulses to let food in work bowl fall to bottom.
Always use the Food Processor button for pulse/chopping. Never turn cover back and forth to start and stop processor.

You can download manual from the below link

http://www.cuisinart.com/share/pdf/manuals/bfp-10ch.pdf

ENJOY! RATE THIS SOLUTION
RNJ VINOD KUMAR

Sep 12, 2009 | Cuisinart Food Processors

1 Answer

Unit assembled, lights are on (pulse, on) nothing happens


The Kitchenaid food processors have a few safety features implimented. If the unit is not assembled properly, this may prevent the unit from turning on. I am thinking this is an issue of assembly because the light is on, so the unit is definitely getting power.

Proper assembly is below:

If it isn't all ready, please disassemble the entire unit. This means removing the blade and/or disc, blade, removing work bowl, work bowl lid, and blade.

Start by placing the work bowl onto the motor base. The work bowl handle should be facing at 9 o'clock, which is out to your left. Rotate the handle downward until it locks in at the 6 o'clock position, which will lock over the center of the button panel.

Repeat the process with the work bowl lid. The blade does not need to be present for the motor to engage, if this is an assembly issue.

Jul 19, 2009 | KitchenAid KFP740 Food Processor

1 Answer

Bravetti EP 199 Need Manual


Type in bravetti in search bar and you may get lucky

Jun 07, 2009 | Bravetti Quad Blade Food Processor

1 Answer

Cuisinart DLC-85 Pro Custom 11 Cups Food Processor. Checked motor as recommended, works fine. Put together as instructed, turned on and when I press the pulse button it turns it off. Help will be...


Whoops, when putting together I failed to insert the feeder cup.  When I did that it worked!  I should have more carefully followed the assembly instructions.  Thanks for your help.  What a great web site

Apr 17, 2009 | Cuisinart DLC-8S Pro Custom Food Processor

5 Answers

Regal La Machine 1


If you still need the book, I might have one I can copy and e-mail to you. I'd have to look for it. No sense my looking for it and copying it if you already have it at this time. Let me know if you still need it. frnktofini@aol.com

Sep 30, 2008 | Regal Ware K813BK La Machine Food...

1 Answer

Need food processor lid


The lid-lip on my small Braun processor broke too, damn things can't handle being accidentally dropped by a fumble-fingered me!

I still manage to work it, I just need to manually hold the broken bit in place (so the safety mechanism lets the motor start), or just use another long thin doodah, like a wooden kabob skewer, to depress the lever. Not elegant, and it means you have to use both hands at the same time (one to activate the pulse button, the other to hold the skewer in place), but it works.

Anyone had any luck supergluing the broken bit back on?

Jan 18, 2008 | Braun Food Processors

Not finding what you are looking for?
Food Processors Logo

Related Topics:

712 people viewed this question

Ask a Question

Usually answered in minutes!

Top Regal Ware Food Processors Experts

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

yadayada
yadayada

Level 3 Expert

68970 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Regal Ware Food Processor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...