Question about Phones

1 Answer

The top keys of my iphone is not working,but the other bottom hal

Numbers 123456 aren't working but 789*0# & the call button is working

Posted by on

  • bhavna_gud Dec 27, 2008

    NONE OF THE KEYS ARE WORKING AND I CANNOT CALL ANYBODY...I CANT SEE MY CONTACTS.....NEITHER FAVOURITES.....

  • Anonymous Jan 19, 2009

    Dude i have a same problem i need help

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You need to replace the touch pad. like go into an apple store and explain to them the problem. and they will fix it. its like a dead strip.

Posted on Jan 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Numbers 7 8 and 9 not working


This is a generalist answer not one specific to this phone!

One of two problems here, the circuit board still has dirt or water residue on it preventing the signals from the keypad from being interpreted properly (a short), or the keypad its self is not conducting the current from the button pads properly when pressed.

Because there are three keys not working then I would imagine its the first problem as the circuits for a keypad circuit is arranged in a grid and this look like the row conductor is not working.

Damage like this often occurs to mobile phones months after they get wet as they slowly corrode with the smallest amounts of water left sitting in between or under the chips on the boards. If the phone has had water spilt on it then it isn't usually a problem if dried properly, anything else though usually is more of a problem.

The rubber keypad can be removed and washed in warm soapy water. The underside of each button is a conductive rubber and needs to be free of any 'stickyness'. these are usually pretty robust. (Only the rubber bit with the printed numbers on it!)

Once cleaned pat dry, even put it somewhere warm dry, or use a hair dryer.. once your happy there is no water left in the buttons etc put it together and try the phone again. I suspect it wont fix your problem though but that's the easiest fix of the two. If you don't want to pay for it to be repaired then have a poke around as its not going to be much use as it is, you'll need to do a bit of investigative work.

Take the phone apart, look for a track on the main circuit board that goes to each area where the 789 buttons would sit, follow it from the buttons and eventually it will go to a black chip on the circuit board, somewhere between that chip and the button pads is your problem. Look how clean the circuit board is near that chip, its likely the 789 button track goes to one of the pins of the chip and it is shorting to one of the pins next to it. if you confident use a pin and gently scrap between the pins, check both sides of the board in the same area for anything dirt related.

If you can get hold of an air line blow under the chip where the tracks go, (make sure nothing is around that is loose on the board that can blow away)

Other than that without a friend with a soldering iron there's not a lot else you can do.

Nov 19, 2014 | British Telecom Synergy 2110 Cordless...

1 Answer

My iphone wont rebbot


have you tried this?
  1. Reset the iPhone by holding the sleep/wake button at the top right of the device and the home button at the bottom center of the face at the same time.
  2. Hold them both until you see the screen go black. In some cases, you may need to keep holding them even after the red power off slider appears. If it does, just keep holding it.
  3. Wait until the white Apple logo appears.
  4. When this happens, you can let go - the iPhone is rebooting.
If this doesn't work, connect it to the computer with iTunes and restore the software.

Mar 11, 2012 | Phones

2 Answers

Hi there ... We have 4 lines in the office but on one of our M2000 series Meridian phones only the first 2 line buttons receive a dial tone ... How do add lines 3 and 4 to the next 2 buttons?


Programming is done on M7310, M7324 and T7316 sets.
To set up line appearence you need to enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt,
press the show key (top right arrow).
The display should now ask for an extension number. Enter extension number you wish to program the new lines on.
Press the show key (top right arrow)
The display should sat LINE ACCESS
Press the show key (top right arrow) .
The display should say LINE ASSIGNMENT.
Press the show key (top right arrow) .
The display ask for a line number. press list
The display should say line 001: appear & ring
press the next key (bottom right arrow) till it says 003:unaaign.
press the chng key till the screen says appear&ring
Press the next key(bottom right arrow)
The display should say line 004: unassign
press the chng key til the screen says appear&ring
press the Rls key when finished

Jul 03, 2010 | NorStar Meridian M7310 Phone

1 Answer

I NEED TO SET UP 4 PHONES TO HAVE A LINE 5 AND A LINE 6. THE BUTTONS FOR THE EXTRA LINES ARE PROGRAM WITH SOMETHING ELSE. HOW DO I PROGRAM THE PHONES TO HAVE LINE 5 AND 6.


Programming is done on M7310, M7324 and T7316 sets.
To set up line appearence you need to enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt,
press the show key (top right arrow).
The display should now ask for an extension number. Enter extension number you wish to program ringing on.
Press the show key (top right arrow)
The display should sat LINE ACCESS
Press the show key (top right arrow) .
The display should say LINE ASSIGNMENT.
Press the show key (top right arrow) .
The display ask for a line number. press list
The display should say line 001: appear & ring
press the next key (bottom right arrow) till it says 025(or 031):unaaign press the chng key till the screen says appear&ring
Press the next key(bottom right arrow)
The display should say line 026(or 032): unassign
repeat the procedure the same as line 5 for line 6
press the release key when finished

Jun 23, 2010 | NorStar M7310 Corded Phone

1 Answer

How to set up restrictions through line restriction filters


It's best if you use the "reply to post" window below the solution box so you can continue the same thread with the same person.

To set up the restriction filters we'll need to get into programming.
Programming is done on 7310, 7324 and 7316 type sets.
Enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the next key (bottom right arrow).
The display should now LINES.
Press the show key (top right arrow)
The display should now ask for a line number.
Enter line number you want to change the line filter on. ex. 002 = line 2
Press the show key (top right arrow)
The display should say Trunk/Line data
Press the next key 2 times (bottom right arrow) .
The display should say Restrictions.
Press the show key (top right arrow)
The display should say Restriction Filters
Press the show key (top right arrow)
Enter in the restriction filter 25
Press the show key (top right arrow)
The display should say No Restrictions and the ADD soft key should appear on the lower right soft key
Press the add soft key and in the restrictions you want on the line.ex. 011any will bolck int'l dialing but not long distance. 0any and 1any will block long distance, operator assisted calls, and int'l dialing
You can also add overrides by pressing the show key (top right arrow) then the next key (bottom right arrow) .The display should say no over rides and the add soft key should appear on the right soft key.
When finished with the filter press the heading key(top left arrow)
The display should say Restriction Filters
Press the next key (bottom right arrow) .
The display should say Line restrictions
Press the show key (top right arrow)
The display should say Normal:none
Press the change key and enter 25.
Press the next key (bottom right arrow) .
Press the heading key (top left arrow) til the display says Lines.
Press the back key (bottom left arrow)
The display should say Terminals&Sets
Press the show key (top right arrow)
Enter in the extension number of the person you want to allow free use of the line.
Press the show key (top right arrow)
Press the next key 4 times(bottom right key)
The display should say Restrictions
Press the show key (top right arrow)
Press the next key 2 times(bottom right arrow)
The display should say Line/Set restrictions
Press the show key (top right arrow)
The display should ask for a line number.
Enter in the number of the line that was restricted.
Press the show key (top right arrow)
The display should say Normal: none
Change the filter to 00 (no restrictions)
That bypasses this extension from line filter 25
Press the next key (bottom right arrow) .
Press the release key when finished

Dec 23, 2009 | NorStar M7310 Phone

2 Answers

NORSTAR M7310, EVERY TIME I PICK UP MY HANDET I HAVE TO PRESS THE VOLUME UP BUTTON. HOW DO I SET IT SO I DON'T HAVE TO DO THAT?


Programming2.gif is done on 7310, 7324 and 7316 type sets.
Enter programming2.gif by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the next key 7 times(bottom right arrow).
The display should say system programming.
Press the show key (top right arrow)
The display should say hunt groups
Press the next key 3 times(bottom right arrow) .
The display should say Featr Settings
Press the show key (top right arrow) .
The display say Backgrnd music.
press the next key 2 times (bottom right arrow)..
The display should say receiver volume.
Press the show key.(top right arrow) change from use sys volume to use set volume.
Press the release key when finished

Sep 02, 2009 | NorStar Meridian M7310 Phone

1 Answer

M7208 How do I programme the button for hands free


Programming is done on 7310, 7324 and 7316 type sets.Enter programming2.gif by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow). The display should now ask for an extension number. Enter extension number you want to change to handsfree.
Press the show key (top right arrow)
The display should say LINE ACCESS
Press the next key (bottom right arrow) .
The display should say CAPABILITIES.
Press the show key (top right arrow) .
The display say foward no answer.
press the next key 3 times (bottom right arrow)..
The display should say handsfree. Press the show key.(top right arrow) change from none to auto
Press the release key when finished

Sep 01, 2009 | NorStar M7208 Corded Phone

1 Answer

How do I programme my buttons and how do set up the phone for hands free use. The phones were moved and the technician set all the phones to the original settings so none of the phones have hands free...


Programming2.gif is done on 7310, 7324 and 7316 type sets.Enter programming2.gif by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow). The display should now ask for an extension number. Enter extension number you want to change to handsfree.
Press the show key (top right arrow)
The display should say LINE ACCESS
Press the next key (bottom right arrow) .
The display should say CAPABILITIES.
Press the show key (top right arrow) .
The display say foward no answer.
press the next key 3 times (bottom right arrow)..
The display should say handsfree. Press the show key.(top right arrow) change from none to auto
Press the heading key (top left arrow) til the display says TERMINALS & SETS again.
enter in next extension to program.
repeat procedure.
Press the release key when finished

Sep 01, 2009 | Nortel Meridian M7208 Corded Phone

1 Answer

Numering and letering worn off keys


You shouldn't need numbers on the keys, all phones have the same 123 / 456 / 789 / *0# pattern. If you want the letters however, you might try using a label maker with the smallest font/size and doing an old fashion cut and paste onto the keys. (in a hurry, use a Sharpie)

Jun 01, 2009 | Uniden DXAI-3288/2 Cordless Phone

3 Answers

Access voicemail from another line while away from home


The previous solution only works for older machines. I have the same Panasonic model and this works every time.
On your handset, hit the top center button(menu). Touch the arrow down button 7 times. Should say "Initial settings". Hit top right button on handset (display shows this is now the "select" key). Display now shows "Set Answering". Hit top right button again ( select key). Display now reads "Ring Count". Hit arrow down button 2 times. Display now reads "Remote Code". Hit select key again and enter your desired 2 digit remote code. Hit "Off" key. When you call the answering machine from the road, simply enter those same digits. Piece of cake. Enjoy.

Jan 01, 2009 | Panasonic KX-TG5632 Phone

Not finding what you are looking for?
Phones Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Phones Experts

kakima

Level 3 Expert

96576 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Cindy Wells

Level 3 Expert

4758 Answers

Are you a Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...