Question about Clarion DRB2475

1 Answer

Set Clock for a Clarion DB336MP

Does anyone know how to set the clock forthe CB336MP?

Posted by on

  • thebenson5 Nov 25, 2008

    Thank you SO much! I couldn't find the solution anywhere in the net.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 64 Answers

You can find the instructions at: http://akamaipix.crutchfield.com/Manuals/020/020DB336MP.PDF
Page 11 give you info on clock setting.

Or try this:

1) Press and hold the [BND] button, and then
press the [DISP] button to display the clock
display.
2) Press and hold the [BND] button, and then
press the [DISP] button for 2 seconds or
longer.
3) Press the [d] button, then set the current
minute.
4) Press the [a] button, then set the current
hour.
5) Press the [BND] button, then the clock is set.

Posted on Nov 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just bought a car with this stereo. Was working fine and then I accidentally was messing around trying to figure things out and put it in demo mode. Now it's stuck!! Can someone please help?!?!


With the stereo on, hold the large round button in to get to setting menu. When it gets to that, I believe clock adjust comes up first, just turn the knob to get to demo mode and then push the button in. Turn the knob to switch demo off and then push it again. That should do it.

Jan 10, 2017 | Car Audio & Video

1 Answer

So how do wire this set set up to a bridged amp any help would be appreciated


assuming that is a dvc dual 4 ohm speaker, and you have a 2 ohm bridged amp, you run a positive from each side of the speaker into the bridged positive of the power amp, and run a negative from each side of the speaker into the negative bridged terminal of the amp. if, indeed, you have 2 4 ohm voice coils, running them bridged in parallel wiring will bring the load to 2 ohms. if you have 4 voice coils, of 4 ohms apiece, you could run all 4 parallel into the amp, but that would bring the load down to 1 ohm, and you would have to make sure you8r amp can support 1 ohm operation.

Jan 07, 2017 | Car Audio & Video

1 Answer

Pass code to Kenwood kvt 717 without remote


Without a remote control, you can't. Just buy an original or a suitable universal remote control that have set-up code/s for your device, in its code list. If you wish to get more details visit the sites linked here.
http://remotesearch.blogspot.com/ http://electrohelponline.blogspot.com/

Jan 05, 2017 | Kenwood Car Audio & Video

1 Answer

My 2002 mazda mvp ausio system is not working but I can insert and eject the CD but cannot do the in tape cassette also the display is not showing the clock or any thing plz any one tell me whats wrong...


Internal board damage. Also the ribbon cable for the soft load on the cassette is not engaging. This can happen due to just ware from the age of the unit. Cold solder joints are usually the culprit, that is why the display will not light. Check yards for a newer used deck it just might be easier unless you have a shop you can send it to.

Nov 10, 2014 | Car Audio & Video

1 Answer

How do i program a clarion db158r car streo


Go here to download operator guide.http://www.clarion.com/gb/en/support/owners_manuals/select/D_H/index.html

May 26, 2014 | Car Audio & Video

2 Answers

JVC KD-R330 Won't turn off Demo mode - tried instructions. Every time I follow the instructions (Turn on, Hold Menu, push "vol" button, change to Demo off...etc) It doesn't work. In fact, as soon as I...


Hi,

Do you have a Bluetooth adapter plugged into the KD-R330?

A compatible Bluetooth adapter (like the KS-BTA100) usually plugs into the rear auxiliary port of the receiver. It then needs to be "paired" with your Bluetooth device, for example, a Bluetooth phone headset.

What you're describing sounds like what can when no Bluetooth device has been "paired" yet.

If you don't HAVE a Bluetooth adapter connected to your KD-R330....is it possible you accidentally plugged something into its rear auxiliary jack? Or the front auxiliary? In other words, is it possible your KD-R330 receiver is mistaking some other device for a Bluetooth adapter?

Don't know if that helps at all...if there's no adapter issue, and nothing connected to the AUX jacks, probably your next step should be a call to JVC, or whatever number you were given for tech support.

On the bright side, since the receiver turns on, and responds to some commands, you probably didn't mess up anything major in the wiring. And, there's also the possibility the receiver is defective....certainly if this continues, and JVC can't help you, trying a replacement might be worth a try.

BTW, feel free to post a reply...I'm going to look further to see if there's any other documented issue besides an adapter that might cause the problem you're having.

Oct 29, 2013 | JVC Car Audio & Video

2 Answers

How to set clock in 2000 GMC JIMMY


Owners manual: 3-10:

Setting the Clock for Systems with HR and
MN Buttons
Press and hold HR until the correct hour appears on the
display. Press and hold MN until the correct minute
appears on the display. To display the clock with the
ignition off, press RECALL or HR/MN and the time
will be displayed for a few seconds. There is an initial
two-second delay before the clock goes into the
time-set mode.

Setting the Clock for Systems with
SET Button
Press SET. Within five seconds, press and hold the
SEEK right arrow until the correct minute appears on
the display. Press and hold the SEEK left arrow until the
correct hour appears on the display.

Nov 13, 2009 | Car Audio & Video

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

540 people viewed this question

Ask a Question

Usually answered in minutes!

Top Clarion Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4766 Answers

yadayada
yadayada

Level 3 Expert

67912 Answers

Marco Avila
Marco Avila

Level 2 Expert

56 Answers

Are you a Clarion Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...