Question about Polaroid TLA-01911C TV

1 Answer

TLA-01911C connect ot Acer 5920 Aspire, not supported.

I am havong problems connecting the two. When i plug my computer in it recognizes the tv but when i changed the resolution a few times, and the refresh rates, i got no change.

How can i get this to display to work?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 37 Answers

Tv screens dot like to change. the auto settings are normaly the best you can get. the only thing you can do is change your resolution but the screen will go black if you change so it is 2 high

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Fix sound on Polaroid TLA-01911C TV

Audio amp may be blown. A cable may be bad.
What are you connected to?

Apr 04, 2014 | Polaroid TLA-01911C TV

1 Answer

Not really a problem but. I need to remove the base from a Polaroid TV model # tla - 01911c to get it into a box to ship

Good day!!!

all you need to do is to get Philip screw driver and remove all screw that connected to the base of your TV after that you can freely remove that base...

Thanks for using fixya...

Aug 11, 2011 | Polaroid TLA-01911C TV

1 Answer

Need a manual for Polaroid TLA-01911C

May 07, 2011 | Polaroid TLA-01911C TV

2 Answers



The white screen and nothing else usually indicates a failure of the filter capacitors in the power supply board. When these capacitors go out the voltages are not correct so the TV can not power up right. You can rebuild the power board by replacing the bad capacitors and this should bring the TV back to life. Here is a link to a repair guide for this power supply board.

I hope this helps,

Dec 28, 2009 | Polaroid TLA-01911C TV

1 Answer

Using TV as a monitor

It's the PC that has to get the info to the TV!

Dec 23, 2009 | Polaroid TLA-01911C TV

1 Answer

Hi my tla-01911c tv powers on and displays the polaroid logo on the screen for about 30 secounds then shuts down as if there is a power overload or something. any ideas? thanks

Either the power supply/inverter board is bad, or the bulbs are bad - or poorly connected. In my case, the solder joints at the end of the bulbs in the top and bottom were horrible. A quick resolder on the corroded bits and good as new.

Dec 20, 2009 | Polaroid TLA-01911C TV

2 Answers

Polaroid 19" TV TLA-01911C has no picture. Powers up, see logo

I had the same problem. I replaced 14 capacitors on the Power supply board. I used Panasonic FC series. You could look for swollen capacitors or ones that are oozing. For sure replace these. My set had capacitors that are known to cause problems so I replaced all of them even though I saw no swelling of oozing. Be sure you label all connections carefully when you disassemble.

Jan 17, 2009 | Polaroid TLA-01911C TV

1 Answer

TV/Computer monitor

Well, it's great and wonderful that you have a high-speed internet service, but your TV's audio isn't biased about internet connections. You forgot to plug in the line-in cable from the green port of your computer to your TV.

Dec 05, 2008 | Polaroid TLA-01911C TV

2 Answers

Polaroid TLA-04011C

Check the powersupply/inverter board for bad capacitors. Also check the CCFL bulbs in the top and bottom for poor solder connection - replace if necessary.

Nov 08, 2008 | Polaroid TLA-01911C TV

Not finding what you are looking for?
Polaroid TLA-01911C TV Logo

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polaroid Flat Panel Televisions Experts

Dave Naylor
Dave Naylor

Level 3 Expert

834 Answers

The Knight
The Knight

Level 3 Expert

68223 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Are you a Polaroid Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides