Question about Maytag Washing Machines

1 Answer

When washer finishes there is a dripping of water inside unit

Maytag Washer W-12, Listed 745G, Model No LAT 8005 AAE. When washer finishes washing clothes, there is a dripping of water inside the unit where the water supply enter the washer. I do not have a repair manual. Is there a manual availble for this model, or how can I fix the leaking of water?

Posted by on

  • 2 more comments 
  • colefitz Dec 28, 2008

    my unit when off continues to leak water into the cylinder until it is almost full by mourning. We then have to hit the drain cycle to empty the unit.

  • colefitz Dec 28, 2008

    my unit leaks water into the cylinder when not in use. We have to keep hitting the drain cycle when the unit fills up.

  • colefitz Dec 28, 2008

    where can i get a valve.

  • colefitz Dec 28, 2008

    where can i buy a valve

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 367 Answers

What has happened is you have sand in your water valve from your water. This pluggs the water valve and also sticks it open so when the water valve shuts of there is still a small trickle of water coming through the washer. Replace the water and it will fix the problem (no way of cleaning the inside of the valve.) Replace water valve.

Posted on Nov 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag model lat 9605 aae fills with water but want agitate or spin out but works fine on delacate cycle thought it was timer put one on still doing the same thing


replace the motor brushes this is common it wont spin or do main cycles but easy go it does is worn brushes
take one and and check the lenght if its less than 50mm replace them
when they get shorter the motor draws more standing current etc running hotter so....
also check the vacume switch and for and rubbish inside the drum skin

Sep 24, 2014 | Washing Machines

1 Answer

After washer has stopped, it contunes to drip inside the tube


Hi,

Start the washer in a normal cycle, once it starts to fill, unplug the unit from the wall. If the water stops completely its not a water valve issue. If it still drips, replace the water valve to the washer. Good Luck

Jul 12, 2014 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Maytag clothes washer model 2500 aae leaks along bottom edge


Sounds like a hose leak inside the machine. Possibly remover front bottom cover then check all hose connections.

Nov 14, 2013 | Maytag Washing Machines

1 Answer

When washing machine not being used the water drips into the washer tub, it is top loader about 12 yrs old


if the washer is filling up on it's own the water valve is bad,sediment gets inside it doesn't close all the way allowing water to leak through. they show two different valves,when you talk to your parts guy bive him the full model number off of the washer and they are asking for a series number either 83 or 87 so you get the correct valve

Mar 08, 2011 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

How old is this machine


I have the lat 9334 aae washer and still have my sales slip from 12/20/1994. Still runs like a top! Hope that helps!

Nov 24, 2009 | Maytag Dryers

1 Answer

I NEED TO REMOVE THE FRONT OF THE WASHING MACHINE T


There are 2 screws down toward the bottom of the front of your washer. You remove these and grab the front panel and pull toward you and up and the 2 clips at the top will snap out. Hope this helps!

May 20, 2009 | Maytag Washing Machines

1 Answer

Cold water will not run into washer, but drips when washer is off


Take the hose off the back of the washer and remove the screen and you will find it to full of sediment. Clean it out and try again.

Jan 25, 2009 | Maytag Atlantis MAV6000 Top Load Washer

2 Answers

Removing the top


the pressure sensor is inside the control panel, the panel is screwed closed from the rear
you initially check that the plastic air line is attached at top and bottom
top is easy
to reach the bottom
the top of the washer must be removed, unlock the two metal clips at the front ~3 inches from the edges by sliding a putty knife or other blunt blade between the front panel and the top
tilt up the top
visully inspect the air line running from the top left to the bottom of the drum/tank

usually the top comes off
test that first,
because if the bottom is off, there would be water running all over the floor as the pressure sensor attaches below water line

if both hose ends are attached remove the top end and blowe down it, any water in the line messes up pressure readings

the water level sensor is adjustable
remove the water level sensor body from the control panel, there is a lock clip on the right side of the control body
there is a 1/8th nut next to the shaft the knob sits on
clockwise to raise water level
counterclockwise to lower water level
if turning the adjuster has no effect, the spring inside has broken, not weakened, and the control body should be replaced.
water level control bodies are common to many models and makes, the local parts store will have a suitable one, even if labelled ge or kenmore instead of maytag

Aug 21, 2008 | Maytag PAV2300 Top Load Washer

2 Answers

Maytag atlantas top loader water keeps dripping from top of drum


Your water inlet valve is probably leaking by. If the water pressure is too, or if there is sediment build inside the valve, sometimes the solenoids will not close properly. Try cleaning the valve to see if this helps. If not, I would recommend replacing it. Depending on which valve you have, repairclinic.com has two listed for this model washer for $20 to $30. Let me know if this helps, or if you need further assistance.

Apr 23, 2008 | Maytag Atlantis MAV6260AWW Top Load Washer

1 Answer

I have a Maytag washer MOD # LAT 2300 AAE


If the machine does not start.
Make sure the circuit breakers or fuses are functional in the main electrical panel.
Try to turn them OFF and ON again.
You might need to check the thermal or non thermal fuses inside your washer.
If all appears in working order, you might have a burnt motor if no noise comes from it when you pull out the knob.

Apr 07, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...