Question about Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 80 series. RUNS LOUD, THEN TURNS OFF AND RESETS...

Hi. My Kenmore 80 series (top loading) recently stopped working properly. My roomate loaded the washer with WAY TO MUCH clothes. Ever since then, the following has been happening:

Washer fills just fine, once spin cycle begins or even a draining cycle, the washer runs pretty loud for about 30 seconds... Then, it just shuts off. It will wait between 2-5 minutes, and repeat again. The washer is spinning while this is going on. It looks to be working while attempting to run. But it seems to shut itself off????

Any ideas???

Thanks so much!

Posted by on

  • gatesteam Nov 24, 2008

    Great! Thanks a bunch! I'm going to give that a shot right now. I'll look online, I hate to be a pest, but would I remove the pump by removing the back from the machine and getting in there that way? Or would I be able to get to that from the loader?



    I'm in the process of removing the back now anyway... Will I notice the pump right away? Or is there something I should be looking for?

    Thanks again!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 291 Answers

You have something gotten into your pump ,,, it trys to drain and spin but overloads the motor and shuts down till the motor switch resets .... remove the pump and take out whatever gotten in it and if that not possable replace the pump.

Posted on Nov 24, 2008

  • Larry Youngblood
    Larry Youngblood Nov 25, 2008

    1st you dont remove the back to get to it ,,,, take the 2 screws out of the console and pull it forward slitly and tilt back, unplug the 3 with plug from cabinet, remove the 2 hold down clips to the cabinet tilt forward and slide off ,,,, the pump is at the bottom with 2 hoses ,,,, only 2 clips holds it on ,,, go back same as taking apart

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore series 80 model 110 wont stop filling!


There is a clear plastic hose that runs from the load selection switch to the side of the washer drum. This hose connects the fill sensor to the load switch. without it being in good condition and connected properly the washer won,t get a signal that it's full.

May 09, 2013 | Kenmore Washing Machines

1 Answer

We have a Kenmore 80 series top load washer model 110.28803890. When the timer moves to spin it makes a load clicking noise and does nothing.


Timers are not supposed to make loud clicks. If it is, it's going bad. The same problem happened with my parent's Estate washer. It its on it's third timer!

May 24, 2012 | Kenmore Washing Machines

2 Answers

How do you remove the top off the washing machine to replace the lid switch in a kenmore super capacity 80 series?


The following link explains step-by-step how to replace the lid switch on a Kenmore top loader:

http://www.fixya.com/support/r3557193-replacing_a_lid_switch

If you have any questions about this repair, please post back and let me know. I hope you find this information helpful.

Oct 26, 2010 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Dryer spontaneously turns on, barrel doesn't spin


If the dryer is more than 10-15 yrs old its probably a good idea to get another one...from what you told me it sounds like a pretty serious electrical problem or short with the Motor or control switch...I wouldn't suggest you try and fix this one yourself...

Apr 20, 2010 | Kenmore Dryers

1 Answer

Kenmore 80 series 110 washer making loud noise during final spin


Make sure all springs are still in their place tilt the machine back and look under it and you can see them. 2nd all legs must be level as well as the floor.

Dec 21, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore Series 80: Loud clicking at spin cycle


sounds like spin tube bad will need to remove basket and gearcase to remove it

Sep 30, 2008 | Kenmore 20172 Top Load Washer

2 Answers

Kenmore 80 Series Top Load Washer not agitating


Check out this you tube. Had the same problem today. Tipped washer on its side and replaced coupler between motor and gearbox. Parts are about $15
This is a good diagnosis video.
http://www.youtube.com/watch?v=VYOP0_KCYT0

Sep 02, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore washer 80 series 4 years old has prob


You may not have the coupling seated properly. However, if the unit is agitating and spinning at the same time, you may have a more serious transmission problem.

Jan 20, 2008 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Kenmore 24032\24036 Top Load Washer Logo

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5433 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...