Question about Garden

1 Answer

Poulan 2150 w/ walbro wt324 carb fuel line reassembly

I am assembling new fuel lines, the old ones are gone.
In the poulan 2150 there is a small and large hole.
On the walbro wt324 there are two attachments points.
I have a primer bulb with a small and large attachment places.

The small line can only go from the tank to the primer bulb, atleast that is only small conections.

Thanks for your help.

Posted by on

  • Anonymous Dec 09, 2008

    I need diagram to see which lines run where and also which line connects to the filter.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 149 Answers

The fule line that comes from the filter/ pick up will go straight to the nipple usualy the one closest to the middle of the carby.
the other hose comes from the carby to the in or **** side( punp it you can feel it)of the primer and then goes to the tank that is the return/ prime, nothing is conected to it in the tank. if you have the carby one the wrong way around it will not prime. just swap them over..

Posted on Jan 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What kind of carb cleaner should I use to clean my lawnmower carb


mower fuel in an ice cream container

(unleaded petrol )
a new pastry brush or paint brush

air compressor would be handy to blow the rubbish off before opening up the carby
and blowing the jets

Jan 13, 2017 | Garden

1 Answer

Remove motar from whisper flo pump


Replacing your pool pump motor
Gather the following items.
Phillips and flat head screwdrivers
Circuit tester
Dry towel
Step One
First, make sure that the power to the pump is turned OFF. This means turning off the breaker at the panel box and not just the switch at the pump.
Step Two - Removing the motor assembly
Remove the four hex head bolts which hold the motor assembly to the pump/strainer housing (These bolts may not be visible).
Slide the motor assembly out of the pump/strainer housing, exposing the diffuser. Pull the diffuser of of the seal plate, exposing the impeller. (The diffuser may remain in the pump/strainer housing. To remove, pull it straight out of the strainer housing.)
There will be a gasket or O-ring sealing between the motor mounting bracket and the strainer housing. Inspect this thoroughly and replace if necessary. An economical option would be to purchase a Go-Kit which includes the pump shaft seal and all necessary o-rings, gaskets and lubricant for your pump.
Step Three
Now, you can lift up the motor with bracket attached to get to the wiring more easily. There may be a bare copper ground wire attached to the outside of the motor that you will need to disconnect. Remove the cover plate on the back of the motor to get access to the wiring. You should have one green wire that is the ground wire and two other wires that are your leads. The lead wires should be black and white but could be any other color except green. Disconnect these wires (they may be attached to a screw, held down by a nut, or clipped on with a terminal clip).
Step Four
Next, you will need to disconnect the conduit (sleeve covering wires between motor and switch or junction box). This usually means unscrewing the compression nut that is screwed on the adaptor which is screwed to the motor. After unscrewing the conduit compression nut, you can pull out the wires from the motor. If you wish to reuse the adaptor, unscrew it from the motor.
Step Five
Now you must remove the impeller from the motor. Remove the volute covering the impeller if it is there. (Some are screwed on). You will need to go to the opposite end of the motor and pop off the plate covering the shaft. The shaft will either have a slot in it for a screw driver or is flattened to allow you to put an open end box wrench on it. This will allow you to unscrew the impeller. You will unscrew in the direction that is opposite to the direction that the veins point at the outside of the impeller. This is the same direction that the motor will rotate the impeller. This may look backwards but the water comes into the center of the impeller and rolls off the veins away from the impeller by centrifugal force. As you take the impeller off, be sure to note how the pump seal is positioned. We highly recommend replacing the pump seal with the purchase of a Go-Kit when replacing the motor.
Step Six
Now you can see the bolts that hold the motor mounting bracket to the motor. Unbolt these, separating the motor mounting bracket from the motor. You are ready to reverse the process to install the new motor.
Step Seven
Important Notes on Reassembly: DO NOT touch the ceramic faces of the seal; This may cause the seal to burn up and leak. Be sure to tighten the impeller completely. Be sure to wire the new motor for 110V or 220V depending on what you have. This may be a simple switch in the motor or you may need to use the wiring diagram on the motor to set for the proper voltage. (Black tracer means the white wire with a black line corkscrewing around it.) Be sure to put the volute back on, aligning properly. Be sure to reconnect the bare copper ground wire to the ground lug on the new motor. When tightening bolts, alternate tightening a few turns at a time to seat evenly or the pump may leak. Fill the strainer housing with water before starting the motor to prime system and prevent damage to seal and impeller.
More Helpful information on how to replace a pool motor
Shaft Seal installation
Clean and lubricate the impeller hub shaft and pump housing seal recess with a dilute solution of non-granulated liquid-type soap
Gently wipe the black, polished surface of the spring seal assembly with a clean, soft cotton cloth. Press the spring seal assembly onto the impeller hub with black polished surface facing away from impeller.
Gently wipe the polished face of the ceramic seat with a soft cotton cloth. Lubricate the O-ring on the ceramic seat and press it firmly and evenly into the recess of the seal plate with polished side facing out.
Place the seal plate onto the motor mounting bracket aligning the positioning lug and guide.
Replacing the impeller and diffuser
Slide the motor assembly, with the diffuser in place, into pump/strainer housing, being careful not to dislodge the diffuser.
Fasten assembly to housing using the four bolts. (Be sure housing gasket is in place.) Tighten alternately and evenly

Oct 03, 2010 | Garden

2 Answers

How do I unclog the carb on my push mower


Haha, nice one, but I am smarter than the average bear.

A PUSH mower does not have an engine, so therefore it does not have a carburetor.

Jan 09, 2017 | Garden

1 Answer

My troy bilt 12av834q711 will start then stop


Might not be flooding - could be that main jet in carb is clogged -unit will start with fuel from primer and then shut down.

Jan 08, 2017 | Troy Garden

1 Answer

What is the air gap between ignition coil and fly wheel on a poulan pro pp4218 avx?


For practical application you can just use a new business card or 3x5 recipe card. You don't want to use same card too many times though because thickens of card will change with use, and exposure to liquids. I don't remember right off hand the exact specs but I do know we have used this method for years.

Jan 07, 2017 | Poulan Garden

1 Answer

I can start my barracuda but it won't run at more than idle


Timing problems, bad or warn cam shaft lobes, fuel pump going bad, no pressure. Worn corroded rubber gas tank lines, from the tank to the hard lines, just forward of the gas tank, under the car. Inspect for gas leaks.

May 28, 2015 | Garden

1 Answer

Hi we have a Massey Ferguson Dyna 4 5465 and it was working this morning and then it died we started it up and it ran for about 1/2 a minute when we try starting it now we can hear the fuel pump runs for...


am i to assume its a diesel ,if so sounds like its out of fuel but i could be wrong as its been many years since i have worked on tractors and all the fancy electronic gizmo on modern vehicles can confuse me.Now firstly check the key as no doubt as its a modern one it has a immobilisor and if the head of key loses its chip inside the key head it will never start unlike the old ones that would run on paraffin diesel or petrol ,the later ones were diesel only but again providing they had fuel and oil with the rad topped up they ran 24/7 ,thats a point check the oil level if its low it may stop the engine from starting

Jan 18, 2015 | Garden

1 Answer

My weed eater will not run with the choke setting wide open.


You may have a pinhole or crack in the small hose that runs from the fuel tank to the carburetor. If equipped with a primer it may also have a small crack or pinhole. Either case may cause the carb to suck air instead of gasoline. Other possible reasons are a plugged muffler causing too much back pressure or a partially clogged fuel filter. (The fuel filter on many weed whackers are located inside the fuel tank at the end of the fuel line.)

Aug 28, 2014 | Garden

1 Answer

I have recently purchased a ford 1510 tractor with a 3 cylinder diesel. It seems to have low power and rough idle problem. Middle cylinder seems to not be firing because when i crack open fuel line to...


Hello, I'm not very familiar w/ your model but it could be a
timing problem, the fuel is not being injected at the right time
to fire. On a older J.D.such as the 820 ect. would not inject at the right time, there is a place on the injector pump that corrects it, however, I would call a ford tractor dealer, or go online to www.tractornet.com
and list your problem. There are many people on this site that can and will help you. Good luck.

Jul 11, 2014 | Garden

1 Answer

L E D christmas lights stay on when shut off.


No it's not. Your LED Christmas lights are okay. Your surge protector is fine too although the switch on your protector is an SPST type - it is connected to one line of your AC outlet. When turned off, the line with the switch is physically cut, but the other line is still alive. Some LED circuits and TFL lights blink even when the switch is turned off, probably because one line of the AC power is still (a)live. If this worries you, just unplug the LED lights from the protector.

Nov 23, 2013 | Garden

Not finding what you are looking for?
Garden Logo

Related Topics:

3,457 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

EugenesDIYDen
EugenesDIYDen

Level 3 Expert

479 Answers

Dennis Key
Dennis Key

Level 3 Expert

2458 Answers

john h

Level 3 Expert

7409 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...