Question about Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Getting error code c1

Who will service my washer in zip code 21740

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Whirlpool Master
  • 3,463 Answers

Hi
Error code C1 indicates problem with drive motor-thermal protector-or motor controller

Overloading may also cause the problem.

Press( stop/cancel) to clear the display.

Hope this helps

Posted on Nov 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer shuts off with an error code of C1. Looks like the bottom of the basket is off-set.


The C1 error is displayed when the motor tries to pull more than 26 amps to run.

This indicates a problem with the motor or motor controller.

Overloading or excessive suds can also cause this error.

If you like to make a few more checks then the image below contains the instructions for entering the diagnostic test mode.

Its a short cycle that runs all of the components so the operation of each can be checked.

I hope this helps but an intermittent C1 error can be hard to pin down.

http://media.fotki.com/1_p,wbrrkqqwkwbqsdgxgtqsskgwtqkq,vi/kdkftbfkwxkfsqdgqsg/1/1303472/5961857/image5668img-or.jpg

From the service manual....

"C1 = Average current limit Or Instantaneous current limit.

If a status signal comes back from the motor controller that a current
limit has been breached, the unit will return to standby mode and
display either CA for average current limit trip or Cl for
instantaneous current limit trip.

Average current trip occurs if there is a 2 second average of current
draw greater than 5.55 amps
at the motor windings.

Instantaneous current trip occurs if there is a spike of 26 amps
instantly at the motor windings.

This may signify problems with the drive motor, thermal protector, or
motor controller. Over-loading the unit may cause this problem."


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jun 28, 2010 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Calypso GVW9959K Top Load Washer: when washing a C1 code appears...


The C1 error is displayed when the motor tries to pull more than 26 amps to run.

This indicates a problem with the motor or motor controller.

Overloading or excessive suds can also cause this error.

If you like to make a few more checks then the image below contains the instructions for entering the diagnostic test mode.

Its a short cycle that runs all of the components so the operation of each can be checked.

I hope this helps but an intermittent C1 error can be hard to pin down.

http://media.fotki.com/1_p,wbrrkqqwkwbqsdgxgtqsskgwtqkq,vi/kdkftbfkwxkfsqdgqsg/1/1303472/5961857/image5668img-or.jpg

From the service manual....

"C1 = Average current limit Or Instantaneous current limit.

If a status signal comes back from the motor controller that a current
limit has been breached, the unit will return to standby mode and
display either CA for average current limit trip or Cl for
instantaneous current limit trip.

Average current trip occurs if there is a 2 second average of current
draw greater than 5.55 amps
at the motor windings.

Instantaneous current trip occurs if there is a spike of 26 amps
instantly at the motor windings.

This may signify problems with the drive motor, thermal protector, or
motor controller. Over-loading the unit may cause this problem."


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

May 18, 2010 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

What is error code C1? Also what causes the


The C1 error is displayed when the motor tries to pull more than 26 amps to run.

This indicates a problem with the motor or motor controller.

Overloading or excessive suds can also cause this error.

If you like to make a few more checks then the image below contains the instructions for entering the diagnostic test mode.

Its a short cycle that runs all of the components so the operation of each can be checked.

I hope this helps but an intermittent C1 error can be hard to pin down.

http://media.fotki.com/1_p,wbrrkqqwkwbqsdgxgtqsskgwtqkq,vi/kdkftbfkwxkfsqdgqsg/1/1303472/5961857/image5668img-or.jpg

From the service manual....

"C1 = Average current limit Or Instantaneous current limit.

If a status signal comes back from the motor controller that a current
limit has been breached, the unit will return to standby mode and
display either CA for average current limit trip or Cl for
instantaneous current limit trip.

Average current trip occurs if there is a 2 second average of current
draw greater than 5.55 amps
at the motor windings.

Instantaneous current trip occurs if there is a spike of 26 amps
instantly at the motor windings.

This may signify problems with the drive motor, thermal protector, or
motor controller. Over-loading the unit may cause this problem."


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Dec 10, 2009 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Calypso with C1 error code.


The CL fault indicates that there was an instantaneous current spike of 26 amps at the motor windings in the washer. This could be caused by overloading the washer. It can also be caused by problems with the drive motor, thermal protector or the motor controller.

You should have been able to clear the display by pressing the STOP/CANCEL button.

If you try running the washer again and continue to get this fault code even with a small or medium load, I recommend calling a service technician to diagnose and repair the washer.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Aug 11, 2009 | Kenmore Washing Machines

1 Answer

Error code c1 of ca


The C1 error is displayed when the motor tries to pull more than 26 amps to run.

This indicates a problem with the motor or motor controller.

Overloading or excessive suds can also cause this error.

If you like to make a few more checks then the image below contains the instructions for entering the diagnostic test mode.

Its a short cycle that runs all of the components so the operation of each can be checked.

I hope this helps but an intermittent C1 error can be hard to pin down.

http://media.fotki.com/1_p,wbrrkqqwkwbqsdgxgtqsskgwtqkq,vi/kdkftbfkwxkfsqdgqsg/1/1303472/5961857/image5668img-or.jpg

From the service manual....

"C1 = Average current limit Or Instantaneous current limit.

If a status signal comes back from the motor controller that a current
limit has been breached, the unit will return to standby mode and
display either CA for average current limit trip or Cl for
instantaneous current limit trip.

Average current trip occurs if there is a 2 second average of current
draw greater than 5.55 amps
at the motor windings.

Instantaneous current trip occurs if there is a spike of 26 amps
instantly at the motor windings.

This may signify problems with the drive motor, thermal protector, or
motor controller. Over-loading the unit may cause this problem."


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question@#$%

Jun 03, 2009 | Whirlpool Calypso GVW9959K Top Load Washer

2 Answers

My Sears Elite Calypso Washer shows a C1 error code


The C1 error is displayed when the motor tries to pull more than 26 amps to run.

This indicates a problem with the motor or motor controller.

Overloading or excessive suds can also cause this error.

If you like to make a few more checks then the image below contains the instructions for entering the diagnostic test mode.

Its a short cycle that runs all of the components so the operation of each can be checked.

I hope this helps but an intermittent C1 error can be hard to pin down.

http://media.fotki.com/1_p,wbrrkqqwkwbqsdgxgtqsskgwtqkq,vi/kdkftbfkwxkfsqdgqsg/1/1303472/5961857/image5668img-or.jpg

From the service manual....

"C1 = Average current limit Or Instantaneous current limit.

If a status signal comes back from the motor controller that a current
limit has been breached, the unit will return to standby mode and
display either CA for average current limit trip or Cl for
instantaneous current limit trip.

Average current trip occurs if there is a 2 second average of current
draw greater than 5.55 amps
at the motor windings.

Instantaneous current trip occurs if there is a spike of 26 amps
instantly at the motor windings.

This may signify problems with the drive motor, thermal protector, or
motor controller. Over-loading the unit may cause this problem."


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Apr 09, 2009 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

C1 code what does it mean on a clypso washer


The C1 error is displayed when the motor tries to pull more than 26 amps to run.

This indicates a problem with the motor or motor controller.

Overloading or excessive suds can also cause this error.

If you like to make a few more checks then the image below contains the instructions for entering the diagnostic test mode.

Its a short cycle that runs all of the components so the operation of each can be checked.

I hope this helps but an intermittent C1 error can be hard to pin down.

http://media.fotki.com/1_p,wbrrkqqwkwbqsdgxgtqsskgwtqkq,vi/kdkftbfkwxkfsqdgqsg/1/1303472/5961857/image5668img-or.jpg

From the service manual....

"C1 = Average current limit Or Instantaneous current limit.

If a status signal comes back from the motor controller that a current
limit has been breached, the unit will return to standby mode and
display either CA for average current limit trip or Cl for
instantaneous current limit trip.

Average current trip occurs if there is a 2 second average of current
draw greater than 5.55 amps
at the motor windings.

Instantaneous current trip occurs if there is a spike of 26 amps
instantly at the motor windings.

This may signify problems with the drive motor, thermal protector, or
motor controller. Over-loading the unit may cause this problem."


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question#$^^

Mar 31, 2009 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Error code c1


Error code C1 indicates a problem with drive motor-thermal protector or the motor controller
may be due to overloading
Press( stop/cancel) to clear the display.
Hope this helps

Dec 23, 2008 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Whirlpool Washing Machine shows error code C1


The C1 error is displayed when the motor tries to pull more than 26 amps to run.

This indicates a problem with the motor or motor controller.

Overloading or excessive suds can also cause this error.

If you like to make a few more checks then the image below contains the instructions for entering the diagnostic test mode.

Its a short cycle that runs all of the components so the operation of each can be checked.

I hope this helps but an intermittent C1 error can be hard to pin down.

http://media.fotki.com/1_p,wbrrkqqwkwbqsdgxgtqsskgwtqkq,vi/kdkftbfkwxkfsqdgqsg/1/1303472/5961857/image5668img-or.jpg

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Nov 22, 2008 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

C1 code


The C1 error is displayed when the motor tries to pull more than 26 amps to run.

This indicates a problem with the motor or motor controller.

Overloading or excessive suds can also cause this error.

If you like to make a few more checks then the image below contains the instructions for entering the diagnostic test mode.

Its a short cycle that runs all of the components so the operation of each can be checked.

I hope this helps but an intermittent C1 error can be hard to pin down.

http://media.fotki.com/1_p,wbrrkqqwkwbqsdgxgtqsskgwtqkq,vi/kdkftbfkwxkfsqdgqsg/1/1303472/5961857/image5668img-or.jpg

From the service manual....

"C1 = Average current limit Or Instantaneous current limit.

If a status signal comes back from the motor controller that a current
limit has been breached, the unit will return to standby mode and
display either CA for average current limit trip or Cl for
instantaneous current limit trip.

Average current trip occurs if there is a 2 second average of current
draw greater than 5.55 amps
at the motor windings.

Instantaneous current trip occurs if there is a spike of 26 amps
instantly at the motor windings.

This may signify problems with the drive motor, thermal protector, or
motor controller. Over-loading the unit may cause this problem."


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jun 23, 2008 | Whirlpool Calypso GVW9959K Top Load Washer

Not finding what you are looking for?
Whirlpool Calypso GVW9959K Top Load Washer Logo

471 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...