Question about Televison & Video

1 Answer

42" vision quest plasma powers on for 2 seconds and powers down

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Changed caps on power supply and bingo it worked thanks fixya

Posted on Dec 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TC-P42ST30 power light blinks twice,replaced power supply board,no change.What to replace next?


Are you SURE you get 2 blinks? I show NO 2 blink code in the 011 model Pana plasma sets. Anyway...if you replaced the PS board and still get a code, unload the VS supply from the SC board and re-check--see if the VS supply comes up--even for a couple of seconds...about 205 volts or so. If it does--re-connect and see if it then does not come up. If not--then the SC board is likely bad (THE most common failure on ANY plasma set is the Scan board ).

Nov 24, 2014 | Panasonic VIERA TC-P42ST30 42-Inch 1080p...

3 Answers

I have had a Hitachi 42" Plasma screen TV for almost 3 years and recently it has had problems. When you turn it on, the TV only stays on for about 10 minutes, and then the screen goes black with the...


The signal from the STU to the Hitachi box is going in the wrong direction.
Is the adaptor that you have switchable? If so, flick the switch in the
other direction and this will fix it. If the adaptor is not switchable get
one that is. Then set the STU output to RGB.

Hope this Helps. -CA

Jul 14, 2008 | Televison & Video

2 Answers

Soniq 42'' QSP424T keeps freezing


I have been repairing Plasma Tvs for some 3 years now and have found most of the problems caused are by Capacitors.Once again Soniq are no different to the others.The fault is on the main Video Control Pcb.Replace Capacitor C529 which is a 470mfd25v.This cap is mounted next to an inductor coil at the top middle of the pcb.This Pcb is the one which has the tuner and all inputs on it.
Good Luck AND PASS THE WORD AROUND. LET US KEEP THE SERVICE INDUSTRY GOING.

VIEWCLEAR VISION PL BRISBANE AUSTRALIA.

Feb 16, 2010 | Televison & Video

1 Answer

LG PLASMA 42 INCH WONT TURN ON!


Sure, you will need to replace the power supply circuit board asap. this will fix your issue.

Jun 03, 2009 | Mitsubishi WS-65513 65" Rear Projection...

1 Answer

I GOT A PANASONIC PLASMA TV 2 DAYS AGO..SINCE THEN EVERY 5 MINS A MESSAGE SHOWS UP ON THE MIDDLE OF THE SCREEN SAYING: "NOW IN PICTURE REFRESH MODE. GOING TO RESET SETTING" HOW CAN I FIX THIS...


  • Unplug the TV and plug it again.
  • Press and hold down the front POWER button.
  • If TV doesn't power up, use remote power on while holding down the button on the set
  • You will be prompted to chose between STORE and HOME mode... select HOME
You should be good to go.

Jul 09, 2008 | Televison & Video

1 Answer

Phillips 42" plasma power problem


See if the following solution is relevant for you (it worked for me and was worth it):

http://www.fixya.com/support/t182302-maxent_mx_42vm11_turn

Apr 11, 2008 | Televison & Video

4 Answers

Magnavox Plasma HDTV Red light


I had a similar problem with my magnavox tv with the blinking light issue. Eventually it just didn't come one anymore. Looking at other forms they said the problem was a bad capacitor number 2074 located on the power supply board. When I opened my tv, I noticed that the capacitor was bulging and burnt up. I bought a new one labeled 2200uf 35v and did some solder to attach the new piece. Put the tv back together and it works like new. No more blinking light. I hope this helps.

Feb 02, 2008 | Philips Magnavox 51MP392H Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71191 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

yadayada
yadayada

Level 3 Expert

66902 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...