Question about kawasaki Full Suspension Mountain Bike Men

1 Answer

The ''belt'' light came on today on my 2006 kawasaki 750i today.

It has 600 miles on it and as I am 63 years old it has been treated very well and not any bad mud at all. 4 wheel drive has only been used 8-10 times in the last two years. I just use it during turkey season and to drive to my deer stands during deer season.

Please tell me what I need to do. I would like not to have to take it to my dealer as the labor charge is $75/hr. Thanks, Larry

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sometimes your belt light comes on when you belt is not tight enough it happends because your belt get little rips in it and it will become loose.

Posted on Nov 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

07 brute force belt light stay on


First of all, your belt MAY need replaced, depending on how many miles/hours you have on it. But if your belt is not the issue, You may have just tripped the 'belt light switch', which is located in the transmission housing. There is a way to reset the light, as I'll explain, but if it comes back on right away after you start riding again, you will probably need to replace the belt so you do not damage your transmission.

Ok, now, to reset that light---
Get yourself a piece of electrical wire, like 20 or 22awg, about 12" long will do fine. Get a set of small alligator clips and put the alligator clips on both ends of the wire to make a 'jumper'.

Next, take your seat off of your ATV. You will notice, toward the back of that compartment, just in front of your little tool pouch holder, there is a wiring harness. Disconnect that wiring harness. Flip the female end up towards you and you will see 4 little connection pins sticking out. Take your alligator clips and hook the clips to the 2 bottom pins in that half of the connector.

Next, turn the key on.

Now, on the right side of the ATV by where you put your foot, you will see the engine brake actuator mounted to the side housing of the transmission case. There will be a wiring harness coming from the actuator. The wiring harness splits into 2 different sets of wiring harnesses. Find the smaller one of the 2, (it will be the one that goes up into the box on top of the housing--that box is the switch) and disconnect it. Let the belt light flash for about 5-10 seconds.

Next, just turn the key off.

Plug the belt switch harness back together, remove the jumper from the back harness and plug that harness back together. You should hear the actuator run for about 5 seconds (it is resetting the engine brake system). Put the seat back on. Start it up and try it out. Have fun!!

Dec 28, 2010 | kawasaki Full Suspension Mountain Bike Men

1 Answer

Kawasaki mule heat light staying on


Replace the impeller in your water pump. It's an easy job and needs to be done every 2 or 3 years depending on use. Why they put a rubber impeller in these I do not know. Your local Kawasaki dealer will be able to help you with the part.

May 23, 2009 | kawasaki Full Suspension Mountain Bike Men

1 Answer

I have a 2006 kawasaki 650 brute force ATV the belt light is on


if its belt driven, they work off a type of clutch that just puts pressure on the sides of the belt. not usaully adustable, but there are mods, and after market clutches for faster respose and more aggressive take off, if this is what your after.

May 11, 2009 | kawasaki Full Suspension Mountain Bike Men

1 Answer

Diff lock is hanging up


does it disengauge when you roll forward while turning bars back and forth.that unit has diff lock cable? check to see it is adjusted right.

May 03, 2009 | kawasaki Full Suspension Mountain Bike Men

1 Answer

What does the F1 red light mean on a 2006 kawasaki VX636R motorcycle?


It's not F1 the light is FI F as in Fuel and I as in Injection.
This light should come on for a moment when the key is turned on and then go off.
Regards
Lon from Woodstock

Mar 10, 2009 | kawasaki Full Suspension Mountain Bike Men

1 Answer

A Radio Shack Metal Detector


http://support.radioshack.com/productinfo/DocumentResults.asp?sku_id=63-3006&Name=Metal%20Detectors&Reuse=N

Dec 27, 2008 | Bounty Hunter Digger Metal Detector

1 Answer

Blowin blue with V twin Quad with only 61 hours


I would put more oil in it and would ride the bike and see if the rings will unstick. Just keep a eye on the oil when running it!!! If this doesn't work then a good chance you will need to rebuild the top end.

Nov 22, 2008 | kawasaki Full Suspension Mountain Bike Men

Not finding what you are looking for?
kawasaki Full Suspension Mountain Bike Men Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Sport & Outdoor Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

rjbeg123

Level 3 Expert

272 Answers

Are you a kawasaki Sport and Outdoor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...