Question about Kenwood KDC-MP528 CD Player

1 Answer

Code problem i have my code but my remote is not working what can i do to get my cd player working

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Use the pause/play toggle button go up and down to select the correct number and go left/right to the next slot. And I've forgotten, but you either push and hold the volume control knob or the pause/play until it says confirmed, or something similar.

Posted on Dec 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Kenwood kdc-mpv619 cd player a friend gave me and i hooked it up it tell me enter a code


The one that worked for me was 30337 (not sure if that would work for you).

1) The way I tested it was go to my stereo and I held down the display button + volume up button. (This should remove the - - - - sign but it will still say CODE).

2) Then you press the 5 button on the remote and if the screen says CODEK then you know the remote works.

(to switch from K to C to A to R press the (>>) button on the screen.

3) Enter the code KCAR (the display will say CODEKCAR)

4) Final Step is hold do the fast forward button (>>) on the screen.

It should work for you after that ;-)

Aug 20, 2012 | Kenwood KDC-MPV619 CD Player

1 Answer

I have a Kenwood KDC-W3037. Will this work with any remote controls?


It will work with Kenwood similar models but not with other models as the codes are different with all makes and models.

Aug 19, 2011 | Kenwood KDC-W3037A CD-receiver,...

1 Answer

I have a kenwood eXcelon KDC-X759 and after i hooked it up it just kept flashing code off, and it will take a cd but no sound and the radio works fine


does the cd seem to be working other than no sound? if so, are you running the audio through an amplifier? if you are using an amplifier, you may be using the antenna remote wire (blue) instead of the amp remote wire (blue/white stripe) to turn the amp on. when using the antenna remote wire it turns off when going to cd mode.

Aug 13, 2010 | Kenwood eXcelon KDC-X759 CD Player

1 Answer

Code for a kenwood kdc 319 cd player


i think the security code on most kenwoods is KCAR. you have to enter the code from the remote control though.

Oct 22, 2009 | Kenwood KDC-319 CD Player

2 Answers

Kenwood KDC-319 CD Player Code dont have a


dont put a code all those radio say that when first power up just push the source button to do what you want

Sep 11, 2009 | Kenwood KDC-319 CD Player

1 Answer

I have a kenwood kdc-722 cd player and i dont know the code


yes the remotes are universal as long as it matches the series and production line you should be good

Apr 28, 2009 | Kenwood Sirius KDC-722 CD Player

1 Answer

Clarion dxz665mp cd player


I think you connect the wrong remote wire to the subwoofer amp.
This cd player it has 2 blue remote wires,one is for PWR ANTENNA (BLUE ONLY),when you insert the cd,this wire cut out the pwr,so,is when your subwoofers stop working.
The other blue wire is the REMOTE (BLUE W/WHITE) Wire,this is the one you need to connect to the Amplifier.

Let me know if work
Thank you

Jul 27, 2008 | Clarion DXZ665MP CD Player

2 Answers

Code for kenwood cd player


get a hold of a kenwood remote that has the alphabet printed on it then enter the code-- KCAR

Oct 14, 2007 | Kenwood KDC-MP228 CD Player

1 Answer

Kenwood MP4029 4 code reset



KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!

Oct 13, 2007 | Kenwood KDC-MP228 CD Player

Not finding what you are looking for?
Kenwood KDC-MP528 CD Player Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio Receivers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Kenwood Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...