Question about HP Officejet 7130 All-In-One InkJet Printer

3 Answers

Hp 7130 all in one failed alignment

Set up and ran install. test page comes out with little if any print.I've taken all the heads out and cleaned them with rubbing alcohol. Put in new cartridges. still not success. Have searched for new drivers and found that I've got the right ones... NOW WHAT! Cindy

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

There's an important step that HP leaves out. Even a check of their faq.'s will result in wrong information. I finally checked with live help and this is the advise that finally worked:
How to fix the repeat alignment issue with HP All-in-One Printer

Posted on Feb 01, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 95 Answers

Hi,


Check the following link

http://h10025.www1.hp.com/ewfrf/wc/document?docname=bpu00657&cc=us&lc=en&dlc=en&product=91466



However, perform the following steps:


1. Verify that the unit is switched on. Unplug the all-in-one from power and disconnect the connection port.
2. Wait 30 seconds.
3. Plug in the power only.
4. Repeat steps 2-4 two more times.
5. On the third time after plugging the unit into power, reconnect the connection port from the all-in-one to your computer.


1. Unplug the power cable from printer when the printer is powered on and wait for 20 seconds.

2. Then, press and hold # and 6 while plugging in the power cord.

Continue holding until it displays Semi Full Reset message in the front panel of the All-in-One.


Regards,

Sagarjd

Posted on Nov 23, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hello,
I ended up replacing all the printheads in mine and it worked fine!

Posted on Apr 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Printer will not copy when selecting black ink, page come out blank,will copy page in color but will not print the black sections


either download the hp program for that specific printer from the hp website or.... turn power off unplug press power button to drain all power disconnect from your computer. In your device and hard ware settings delete the printer or uninstall it. Now in this order exactly plug power cord back into printer and power on next plug com cable or usb cable back into computer from printer let your computer install the drivers and programs all over again and when this is done it should be reset now print a test page and enjoy

Apr 12, 2014 | Office Equipment & Supplies

2 Answers

Installed new cartridges - prints color not black


Hi Colleen,

Try this > open a document (from the computer) and select print from the menu,
- In the print screen window select 'properties' Or 'Preferences' or 'Properties'

- In the next window click 'maintenance'

- In the next window there will be many options to clean, align, nozzle check etc etc... , there click 'Ink cartridge settings'.

- A small windows opens, there select black only. See the image

- try printing, if it fails to print, just return the crtridge to the shop and get a geniune branded one. (dont forget to change the 'inak cratridge settings to normal to 'both black and color')


Hope this help, if you are not able to fix it still, then better come to chat http://www.fixya.com/marketplace/servicepage.aspx?srvid=17981 , thanks!


10_22_2011_5_43_18_am.jpg

Oct 22, 2011 | HP Photosmart C6380 All-In-One InkJet...

1 Answer

HP Officejet Pro L7780 all-in-one, Windows Vista, set up as a wireless network printer, prints multiple copies of test page and also other documents, when only one is selected both at the computer and...


this is a simple problem, the technology that printer aligns its print head automatically by the reading the align page, if your printer head are not in good health/clogged align print wont come properly result align pending..When printer gets power on its prints align page till align completes. Go to tool box in system all programme, perform clean print head, check the quality of printer outs then ask to printer to align.. if its not completing replace print heads..

Sep 10, 2011 | HP Officejet Pro L7780 All-In-One InkJet...

1 Answer

Hp7130 printing blank pages


Clean the printer head or check the cartridge, try to print a test page. Let us know the result.

Good Luck

Feb 24, 2011 | HP OfficeJet 7130 All-In-One Printer

1 Answer

My hp officejet 6210 all in one is instaled under general heading: officejet 6200 series. Result: the printer reacts to command given by laptop windows xp but does not print given text. The paper comes out...


Are you able to print Self test page from printer ( standalone ) or able to make a copy ? if you are able to make copy/print self test page from printer, this issue is with Printer Drivers, You can uninstall and reinstall the software ( download the latest software and drivers from HP website )

If you are not able to make copy/print self test page from printer, it is issue with printer/cartridges... you need to re-align the printer

to clean/align cartridge
On Printer Front panel
Press - Setup Button ( press ok)
Press - Tools ( Press Ok )
Press - Clean Cartridges ( Press OK )
And/Or
Press - Align Cartridges ( Press OK )

Jun 22, 2010 | Office Equipment & Supplies

2 Answers

C6180 failed alignment test, will not print color properly


All colors need to be present to pass alignment. Usually what I see is the yellow is empty. You can blot the print cartridge on a damp paper towel to verify the inks are working and this also cleans the head.

Jun 29, 2009 | HP Photosmart C6180 All-In-One InkJet...

2 Answers

Printer keeps showing : Press enter to align cartridges. After doing this it then prints out an alignment page and shows: Alignment failed please: Press enter Alignment failed. This goes on and on. I have...


I have found that if I put in an old aligned page the printer reads it as and the alignment is accepted. As for the cancelled message being in the window, I have had this problem too. I've ignored it and selected the copy button and it took the command. The only problem with hitting cancel is that you cannot turn off your printer. Every time you do you have to repeat the aligning and cancellation process.

May 02, 2009 | HP Officejet 5610 All-In-One InkJet...

1 Answer

Test page quality bad


When I scan a document it prints out small. How do I change the size?

Feb 21, 2008 | HP Photosmart C4280 Aio Printer

Not finding what you are looking for?
HP Officejet 7130 All-In-One InkJet Printer Logo

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Vinaya Kumar...
Vinaya Kumar...

Level 3 Expert

1121 Answers

Seeker5211
Seeker5211

Level 3 Expert

1088 Answers

kakima

Level 3 Expert

98868 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...