Question about Hotpoint  Standard Range Hood

1 Answer

INSTALLING NEW HOOD VENT RE CIRCULATING NO DUCT

CAN I SPLICE AN EXT CORD AND ATTATCH IT TO THE WIRES IN THE HOOD AND PLUG IN WALL SOCET BEHIND STOVE, WHICH IS 120V, HICH IS POS AND WHICH IS NEG ON THE EXT CORD.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 333 Answers

The white which has the longer slot is the negative and the black wire which has the smaller slot is the positive ( hot ) wire.

Posted on Nov 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace?


Kitchen hood replacement can be completed easily with a family member or a friend. While you may wonder why anyone would replace a kitchen hood, the answer usually is simple. Here is how to replace a kitchen hood.
Tools Needed

  • New Range/Kitchen Hood
  • Screws
  • Screwdriver
  • Friend
  • Wiring Nuts
  • Circuit Tester

Warning: Remember that you are dealing with electricity, so stay away from water and use all safety precautions issued by the manufacturer.
Step 1 - Shut off Electricity

Remember to turn off the electrical supply to the old kitchen hood. You will need to do this via the circuit breaker box. Wait for 10 to 20 minutes and then test the wires with the circuit tester to double check that no electricity is being supplied to the kitchen hood.

Step 2 - Remove Old Hood

After you know for a fact that it is not receiving an electrical current, you can begin the process of removing the older kitchen hood. You should first take off the electrical wiring cover that is located by the light fixture. Then have your family member or friend hold up the old kitchen hood while you remove any screws or bolts from it. Once that is done, you can then freely slide it off.
Step 3 - Check Wiring

Double check that you have at least 12 inches of wiring to connect your kitchen hood to the wall. It should be noted that if you have a kitchen hood without vents, proceed to step 5 next.
Step 4 - Find the Ducts

If your new kitchen hood has vents, you will need to locate the fan or vent duct. Once you have found it, you can open up the vent hole where it will belong.
Step 5 - Wires

Open up the covering for the wiring and put the covering in a safe area for easy reach.
Step 6 - Install the New Kitchen Hood

Have your friend or family member hold up the kitchen hood and mark the areas where the screws or bolts will be. Then have them put down the kitchen hood and screw in the screws half way into the holes. After that, you can slide in the kitchen hood.
Step 7 - Route Wiring

Lightly pull the wiring through the proper holes and connect both black wires from the new kitchen hood to the black wire from the wall with a wire nut. Then connect the two white wires from the hood with the white wire from the wall, again using a wire nut. Next, connect the green wire to the green ground screw. Then place the wire covering back on.
Step 8 - Tighten Screws

Finish tightening the screws in place.
Step 9 - Test

Check to make sure the fan and light work. If it is supposed to vent outside, make sure that the air is leaving the vent with no issues. If something does not work proper, repeat steps 6 and 7 until everything works well. Remember that you will be working with electrical equipment, so follow safety measures issued by the state or the city.

Jan 29, 2011 | Kobe RA9436SQB Kitchen Hood

2 Answers

Range hood installation


you can reseal the hole with aluminium tape
you can use screws with metal flat washer that has a rubber backing

May 28, 2009 | Broan-NuTone Allure III QS330SS Kitchen...

2 Answers

Can this be installed over an island?


Bring a focal point to your kitchen by having an island range hood, combining function and elegant form. A suspended hood is also an efficient way to vent
grease, odors and smoke to the outside from a island stovetop while you cook. You can install an island range hood in just a few hours with the right tools
and knowledge.
1.Wear safety glasses and work gloves. Turn off the electricity to your kitchen at the circuit panel. Cover the circuit breaker with a piece of electrical
tape to prevent people from turning the on switch while you are at work.
2.Lay work drop cloths on your cooktop and floor to catch dust and debris. Mark the duct opening with a pencil in the ceiling, where the island hood will be
installed. Be sure the opening is centered directly above your cooktop. Cut the opening using a hacksaw.
3.Go up to the roof, using a cat's claw and hammer to remove stucco, tiles, sheathing and insulation to make way for the steel venting duct. Drop a
plumb bob down the roof, making sure the line is straight down for the ductwork.
4.Follow the manufacturer's instructions for locations, installing 2-by-2 wooden blocks in the ceiling to hold the ductwork hangers.
5.Install the venting duct from the outside of the home, down to the location of the exhaust vents on the island hood. The ducts should easily slip into each
other. Secure all the duct sections with duct sealing putty, using a putty knife.
6.Screw a roof cap on the end of the duct at the roof. Seal any openings or gaps where the roof, ceiling and duct meet with silicon sealant. Let the sealant
dry, then paint with colors matched to the surrounds.
7.Place your hood upside-down on the floor, with the fan and filter facing upward. Locate and unscrew the metal electrical box cover on the island range
hood, to expose the wiring
8.Install the hood cover to the load-bearing ceiling frame with the package hardware through the four inside mounting corner flanges on the cover.
9.Measure what will be the distance from the bottom of your hood to the cooktop; it should not exceed 30 inches for exhaust efficiency. Have a helper hold
the hood in place while you attach the hood on the hood cover using the included screws. Use a level be sure the hood is level as mounted.
10.Connect the electrical wiring by consulting the manufacturer's suggestions or hire an electrician if you are not familiar with house wiring. Tuck the wires neatly in the hood electrical box and then replace the cover, after connecting the hood wires to the wall wiring.
11.Remove the electrical tape on the circuit breaker, turn on the electricity to your kitchen and test your island range hood.
8_9_2012_9_29_10_am.jpg

May 26, 2009 | KitchenAid KHVU781RSS Stainless Steel...

1 Answer

Electrical hookup


If you have the hot and common wires connected (black to black and white to white) it should work. If not, try connecting a length of wire to the ground wire and connect to ground, such as a copper cold water pipe, radiator, heater vent, or the ground terminal in a nearby outlet. If it works then, you need to splice an extension to the ground wire to connect in the box where the hot and common are. Keep in mind all splices must be inside an approved box. If it still doesn't work, yours is not the first nor the last defective hood to be sold.

Feb 28, 2009 | Broan-NuTone Allure III QS330SS Kitchen...

1 Answer

Venting hood to outside wall.


install ducting along with closing flap (so outside wind does not blow in) and power first !

Jan 25, 2009 | Jenn-Air JXT8142ADS Kitchen Hood

2 Answers

Jenn-Air Downdraft ducting roof Rack w/flapper


go to www.luxurymetals.com
there are many good high quality vents on the site

Oct 08, 2008 | Jenn-Air HV363 Kitchen Hood

1 Answer

Damper need for Broan Range Hood


I called tech support at Broan and was told they recommend two dampers in cold climates ...one at in the wall cap and one on the unit. They make the damper,
(#BP87-7"), that attaches to the round duct plate that comes with the hood. Strangely the unit does not include a round damper and the seller LOWES did not have it, also checked Home Depot,.
The Tech said they can't get stores to stock it. I checked at a local supplier of all kinds of plumbing, heating, and cooling supplies and they only had basic 7" dampers which, I was told would probably be too heavy, and be manual. I ordered it through Amazon/True Value ($11.56 w/ shipping, shipping more than cost of damper). Tech indicated that the 2nd (unit damper) is optional and may not be needed if in a warm climate. I would suggest that Broan include the $5.00 item in their unit or at least sellers stock it.

Jun 27, 2008 | Broan-NuTone Broan Range Hood Accessory

2 Answers

Does not take up the smoke or steam - 2nd unit


It really depends on the exit. If the duct exit has to travel really far before exiting it tends to not have as much suction. And like solution 1 said. Make sure the plate was removed

Apr 12, 2008 | Broan-NuTone Allure II QS230SS Kitchen...

1 Answer

Lack of steam removable from microwave


Microwave vent systems are shallow with no capture area to collect your expanding water vapor, they are flat on the bottom. To increase the efficency make sure that you duct it to the outside. If you want to keep your micro/hood vent you will have to boil on the back burners, it is the nature of the product.

Feb 18, 2008 | Range Hoods

Not finding what you are looking for?
Hotpoint  Standard Range Hood Logo

Related Topics:

452 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Range Hoods Experts

yadayada
yadayada

Level 3 Expert

60557 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Hotpoint Range Hood Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...