Question about GE Kitchen Ranges

Open Question

GE Profile model# JS968S0F3SS SERIAL# VF2017560 1) WHAT IS THE PROBLEM FOR FUNCTION ERROR CODE (FO) 2) WHEN I USE CONVECTION THERE IS A VIBRATION SOUND

Posted by on

4 Suggested Answers

jsrock516
  • 5911 Answers

SOURCE: GE Wall Oven - error code F1

According to GE, the F1 fault code indicates a problem with the Electronic Range Control (ERC) Board. If the fault cannot be cleared, they recommend replacing the ERC and the touchpad. Has your repair guy tried any of these ideas? Post back with your comments, please.

Posted on Jan 17, 2008

sdmc73
  • 121 Answers

SOURCE: my ge profile dual stove shows up ''FO''

f0 is a fault code that is the erc failed

Posted on Nov 29, 2008

  • 958 Answers

SOURCE: I have a GE Profile flat top stove model

http://www.applianceaid.com/fault_codes.html

Posted on Nov 12, 2009

  • 38 Answers

SOURCE: GE profile XL44 code F7 & FO readng on

Turn the circuit breaker off at the switchboard for a minute then back on again. This may reset the electronics.

Posted on Nov 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Receiving F7 error code while cooking turkey model # GLEFM397


FIXED GE Profile Oven F7 error messages - ApplianceBlog

www.applianceblog.com/.../2655-GE-Profile-Oven-F7-error-messages

Jan 13, 2006 - 10 posts - ‎2 authors
My GE Profile built in convection/thermal wall oven constantly flashes F7 errormessages. ... Three of my neighbors and I have the same GE profile double oven (new home development) and we've all have the same problem as you described-F7. ... GE Oven F7 error message solution. LG Electric oven not heating. F7 error code
2 posts
Jun 9, 2015
FIXED Kenmore Double Oven error code F0 and F7
10 posts
Aug 31, 2010
More results from www.applianceblog.com

Nov 14, 2015 | Frigidaire Kitchen Ranges

1 Answer

We have a GE Profle XL44 Self Cleaning Dual Fuel Convection range that just started displaying an error code "F0". What is the issue? Can the oven/stove top be used while assessing this...


Hi

F0 Error indicates a bad control board and the control board (electronic control) should be replaced to solve this issue. Hope this helps...please post back for further assistance.

Daniel

Aug 08, 2011 | GE Profile 30" Self-Cleaning Slide-In...

1 Answer

I am getting a F4 code when I use my sensor buttons on my GE Profile Sensor Convection Micro - Model JVM1190WY 004


i have jvm1190sy. when i press a popcorn button it says f4 and making sounds... how do i fix my solution?

Sep 29, 2010 | GE Kitchen Ranges

1 Answer

Oven will not work.


This is what GE recommends for your oven:

“F—and a number or On models with a door latch, • The latch may have been moved, even if only slightly,
letter” flash in the display if a function error code appears from the locked position. Make sure the latch is moved
during the self-cleaning cycle, to the right as far as it will go.
check the oven door latch.
You have a function error code. • Touch the Clear/Off pad. Allow the oven to cool for
one hour. Put the oven back into operation.
If the function code repeats. • Disconnect all power to the range for 5 minutes
and then reconnect power. If the function error
code repeats, call for service.

May 18, 2010 | GE Profile Spectra JGBP90 Gas Kitchen...

1 Answer

GE profile XL44 code F7 & FO readng on


Turn the circuit breaker off at the switchboard for a minute then back on again. This may reset the electronics.

Nov 22, 2009 | GE Kitchen Ranges

1 Answer

My Frigidaire FGFL67DBF gas oven does not reach the temperature set. I tried to calibrating the control, but it did not work. Any suggestions?


I believe that you have a convection oven.... by design, convection ovens built by GE come up to temperature....at 25 degrees below the set level .... when the Convection function is enabled.

Oct 15, 2009 | GE Profile Spectra JGBP90 Gas Kitchen...

3 Answers

GE Wall Oven - error code F1


According to GE, the F1 fault code indicates a problem with the Electronic Range Control (ERC) Board. If the fault cannot be cleared, they recommend replacing the ERC and the touchpad. Has your repair guy tried any of these ideas? Post back with your comments, please.

Jan 17, 2008 | Kitchen Ranges

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...