Question about Raypak Pool & Spa

2 Answers

Raypak 2100 digital heater give fault code eol

How do you reset code?

Posted by on

  • rbp6 Feb 08, 2009

    I have the same problem with my RayPack 2100, There IS an error code EOL. I am looking at it on my control panel now. I cannot move from the pool setting nor change temperature settings up or down. When I push the down temperature, the setting automatically goes to 54 and shuts down.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 22 Answers

ILO or ROL. There is no EOL.

ROL is a switch inside the lower left corner of the heater. Press the red button. ILO is a lockout. Power down and power up.

Posted on Dec 21, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Ffl message

Posted on May 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ROL keep displaying on my raypak rp 2100


check gas pressure if too low it will overheat replace rollout fusible link if it happens again you might need a vent stack

Jun 23, 2012 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

1 Answer

Raypak 2100 just get SPK then LO codes. won't ignite


if wired 120 volt check wiring and check gas pressure see if lines have cobwebs

Jan 02, 2012 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

1 Answer

Raypak 2100 pool heater won't heat, PRS and HL2 error codes.


Well, I replaced the pressure switch with no joy. I tried all 5 levels of pressure 1-5 and every wiring combination. Finally, I returned the new $70 pressure switch and took the 2 wires and tied them together (jumped them). Here's the only downside...If you run your pump in backwash, recirc, waste, or any mode that would cause water to bypass the heater it MUST BE OFF. Otherwise, let it ride. It's working great and I hope to go into October weather permitting.

May 11, 2010 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

1 Answer

RayPak 2100 series digital pool heater Code "EOL".


press the mode button until the display reads "off". Remove the four screws holding the control cover on. Swing panel down so that the back of the board is visible. Press the mode button until "RESfl" appear. Press and hold both "up" and "down" buttons for 5-7 seconds until three dashes appear (---). This resets the fault history and clears any stored faults.

Sep 05, 2009 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

1 Answer

Pool heater will not work


Eol is a manufacturers code meaning End Of The Line. I have never seen this displayed on any malfunctioning heater that I've serviced. Try shutting down the power to unit and resetting the board.

Apr 09, 2009 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

1,820 people viewed this question

Ask a Question

Usually answered in minutes!

Top Raypak Pool & Spa Experts

Bill Jordan

Level 2 Expert

372 Answers

paulcarew

Level 3 Expert

2364 Answers

yadayada
yadayada

Level 3 Expert

70347 Answers

Are you a Raypak Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...