Question about RCA D52W20 52" Rear Projection HDTV-Ready Television

1 Answer

The power light blinks 3 times and never comes on

When I push the power button it blinks 3 times and never comes on. It does that all the time.

Posted by on

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • RCA Master
  • 8,617 Answers

You need to replace the flyback 259296 and CP150 you van get both parts with free instalation instructions at the following link.
http://servicemanuals.vstore.ca/

Posted on Nov 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My tv won't turn on when the on button is pushed, but the power light blinks 5 times


5 times LED blinks in Panasonic PT-47WX42 shows problem with convergence out chips failure as this tv has two big black ICs STK392-110 as convergence output, replace them to fix tv problem.

Jan 28, 2013 | Panasonic PT-56TW53 56" Rear Projection...

2 Answers

I push the power button standby light turns red & blinks 3 times 7 THEN TURNS OFF


If the standby light is flashing 3 times. (your post says 3 times 7) I was unclear... A error code of 3 blinks inidicate that the door covering the lamp is not secure oer the lamp is not secure. Make sure the lamp door is seculy screwed down. ussally the door push a little switch closed. If this doesnt work the next thing to try is to remove the bulb carefully(dont touch the lens) and replace it making sure the bulb is in place securely. let me know if i can help any further

Mar 04, 2011 | Sony KDSR50XBR1 50" Projection HDTV

1 Answer

When the tv plugged up the power led blinks 3 times. When the power button is pressed the tv comes on for three seconds and turns back off. What could be the problem? Could this be a convergence problem?


Do the self check when power light goes out:

ON front of set (not remote) press and hold both the Menu and Input (Device) buttons at same time for 5 seconds or longer and release both buttons.

Power light will blink a two digit error code like 2 blinks, 2 blinks, a pause and repeat it several times.

Let me know code.


SD TECH

Sep 24, 2010 | Mitsubishi WT-46809 46" Rear Projection...

1 Answer

When you push the power button, the fan comes on..If you then push the lamp button, the lamp lights up then immediately goes out and the temperature indicator light goes out and the power button blinks..


it sounds like you need a new lamp, this lamps are rated 6000-8000 life hours a life span of 2-3 years of use most of the time the problem comes from the lamp in this TV sets this is the lamp you need

http://cgi.ebay.com/ORIGINAL-HITACHI-UX21511-DLP-LAMP-REPLACEMENT-BULB-OEM-/120607006394?pt=LH_DefaultDomain_0&hash=item1c14bcdeba

Sep 20, 2010 | Hitachi 60V500 60" Rear Projection...

2 Answers

Series of 3 blinking lights. manual says lamp door isnt fastened properly. it is. i tried unplugging tv, have opened and closed lamp door 3xl. still blinking.


After I unplug and then plug tv to reset I get a solid standby light,then when I push the power button I get a green light that blinks 6 times then it blinks red 6 times and then red 6 times continuosly with a slight delay between the 6 blinks of red.

Oct 11, 2009 | Sony Grand WEGA KDF-60XBR950 60" Rear...

1 Answer

Panasonic PT-53TW53G


If the front power light is blinking three times then your TV has a problem with the convergence. You can get the correct replacement parts and full step by step photo instructions from www.TvRepairKits.com

Aug 17, 2008 | Panasonic PT-53TW53 53" Rear Projection...

2 Answers

Sony Triniton Wega Model KV 32HS510. After pushing the power button,the tv starts to power up, then the standby light blinks 7 times then pauses before blinking 7 times again. It continues to do this,...


This is usually an indication of a failure in the scan amplifier sections. When the scan amplifiers or high voltage sections fail, the main power supply will usually also require servicing.

It is very common that the fly-back and high voltage multiplier and also the horizontal output stage fails in these sets. Along with it, the power supply will usually require to be serviced. On rare occasions, the vertical deflection amp fails.

Jerry G.

Jul 08, 2008 | Sony Grand WEGA KF50WE610 50" Rear...

1 Answer

My projection tv trys to come on but won't you push the button and the power on light comes on but goes off comes back on then goes back off 3 to 4 times then goes off for good started few days ago but if...


I need the model number of your set. And can you count exactly how many blinks the power light blinks when you press power? Please respond to this same post so all comunication will be available for each response.

Jun 26, 2008 | Projection Televisions

Not finding what you are looking for?
RCA D52W20 52" Rear Projection HDTV-Ready Television Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...