Question about Panasonic PT-51DX80 51" Rear Projection Television

1 Answer

Need a wiring diagram

I aquired a panasonic pt-51dx80a and the people i got it from took all thw wires off because they say it just went out on them one day and it is just a resistor that blew so i need a wiring diagram to put them all back together now if anyone can help with that i would appreate it

Posted by on

  • Csquared Cole May 11, 2010

    What resistor is it? R### and I can tell you

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This site has a lot of service manuals with wiring diagrams for a reasonable price. Downloadable PDF in most cases. I have purchased 2 for RP TVs.



https://secureiti.com/servicemanuals/default.aspx

Posted on Jun 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i clean the screen on a panasonic pt-50lc13


I am attaching the diagram that shows how to remove the screen. Its not very big but I can email the full size diagram if it would help.12_24_2011_5_47_56_pm.jpg

Dec 24, 2011 | Panasonic PT-52LCX65 44" HDTV

1 Answer

WOULD LIKE TO GET A WIRING DIAGRAM SO I CAN FIND OUT THE PART NUMBER FOR A CERTAIN WIRE THAT IS BROKEN. THE MODEL NUMBER IS: pt-50LCX64. THANK YOU


You can purchase one for $12.95 from the link below:

http://service-manuals-schematics.com/purchase.php?id=Panasonic+PT-50LCX64+Service+Manual+%2F+Schematics

In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.

If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

May 31, 2011 | Panasonic PT-50LCX64 50" Rear Projection...

1 Answer

Panasonic PT-53TW53G 1 Blinking red light, will not stay on.


just got back today for same problem. convergence went out. took to repair shop. $200 part plus $60 labor. second time in a year convergence went out. was told it will happen again.

Mar 19, 2009 | Panasonic PT-53TW53 53" Rear Projection...

1 Answer

Panasonic PT-51DX80A


Look at the main circuit board do you see any burned resistors?

I had this same problem.

Sep 28, 2008 | Panasonic PT-51DX80 51" Rear Projection...

1 Answer

Panasonic PT-51DX80A


Check your hori out put transistor and next too it is a 1200pf 2k volt cap that goes bad.

Mar 18, 2008 | Panasonic PT-47WX49 47" Rear Projection...

1 Answer

PANASONIC PT-51DX80A


Normally, the main cause of this problem is the solder connection under the convergence IC's.
You would see rings around the legs that have bad solder joints.
My shop would replace both of the IC's.
I don't have a schematic in front of me, but, I'm pretty sure the IC's are STK392-110. We use the STK392-150 in place of them since they are a heartier IC.
When replacing these IC's, remember to use semiconductor compound on the back side of the IC when placing the parts against the heat sink.
Any questions, respond to this post and I will reply.

Jan 27, 2008 | Panasonic PT-47WX49 47" Rear Projection...

Not finding what you are looking for?
Panasonic PT-51DX80 51" Rear Projection Television Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

Josh Whitehead
Josh Whitehead

Level 3 Expert

1146 Answers

The Knight
The Knight

Level 3 Expert

68223 Answers

Are you a Panasonic Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...