Question about Concept CD-2410 Car Audio Amplifier

1 Answer

I have a concept cc-d800a amp. now it doesnt work?

One day i went to work and left my keys on by accident. when i came back to my truck it was filled with smoke and the remote wire had melted the part where you hook up the remote wire. not it doesnt work. Any ideas how to fix it or how much it might cost. is it even worth fixing

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 130 Answers

If you are not an electronic technician you might not be able to fix the amp your self. You can replace the power fuse if the amp does not come on. If it lights up, with out blowing the fuse again, then hook up a speak to the amp and an input. If it plays good. If not and you are not an ET then take it to a repair shop. Amps can usually be repaired, if the cost of repair is not more than a new one.

Posted on Nov 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE A CONCEPT AMP I NEED WIRING DIAGRAM FOR SPEAKER HOOKUP


You may have to contact Concept directly to request the diagram.

Aug 08, 2014 | Concept CC-452 Car Audio Amplifier

1 Answer

How much rms dose amp have?


Concept CC-2502 2002 900 watts max Rms

Feb 24, 2011 | Concept CC-2502 Car Audio Amplifier

1 Answer

How to install cc602


How do you hook up Concept amp CC-452.

Oct 31, 2010 | Concept CC-452 Car Audio Amplifier

1 Answer

How many watts dose a concept cc-752L amp have ?


4 Ohm Stereo Power (RMS): 75W X 2
4 Ohm Bridged Power (RMS): 250W X 1
2 Ohm Stereo Power (RMS): 125W X 2
Signal-to-noise ratio: 100 dB
Frequency Response: 5 Hz - 50 KHz
Total Harmonic Distortion: 0.05%
Input Sensitivity: 200mV-4V
Continuously variable 0 - 18dB Bass Boost
Built-in continuously variable 18dB per octave crossover, from 50Hz to 250Hz

Sep 26, 2009 | Concept (CC752L) Car Audio Amplifier

1 Answer

What speakers


Hello enot99,

The CC-2502 is a bridgeable 2-channel amp. If you want to drive normal speakers in stereo, the best would be a good set of components with separate woofers, tweeters, and crossovers. They are available in many sizes from most car audio manufacturers. I'd begin by finding out what speakers fit the location where you intend to mount them. Then I'd browse the speaker selections in that size at www.crutchfield.com. You can also use the "outfit my car" feature to browse only the products that fit. Then select a pair that has a power range and impedance to match the amp: 250 watts RMS at 4ohms or 450 watts RMS at 2ohms.

If you want to use the amp in bridged mono mode to drive a subwoofer, again Crutchfield has a large selection of subs and some enclosures already fitted with subs (loaded). The amp claims 850 watts RMS into 4ohms bridged, so look for a sub that has a power handling rating of at least 850 watts and it needs to be 4ohms.

Hope this helps.

Aug 02, 2009 | Concept CC-2502 Car Audio Amplifier

1 Answer

Bridging CC-452 or CC-752 amps.


either will work fine, as long as it's a + from one channel and a - from the other.

Jul 20, 2009 | Concept CC-452 Car Audio Amplifier

1 Answer

I need to know how to wire a single 2 ohm sub to a concept cc-d800 to make amp run 2ohm


If your sub is 2ohm it's just left positive and right negative at the amp to the speaker. Hope this helps

Jun 26, 2009 | Car Amplifiers

1 Answer

I have a 2400 watt concept amplifier and if i turn it up too much it sends a real loud hum throught my subs. I really want to get it fixed because this has ben a very good am to me. If i need this repaired...


yes that cause from yhe gain is too high on the amp and you getting a ground loop traveling thru the rca signal
once the gain is high you will hear it make adjust on amp

Mar 29, 2009 | Concept CC-2502 Car Audio Amplifier

1 Answer

Concept CC-2502 Car Audio Amplifier


The amps are probably going into protection mode. The wires are most likely not hooked up correctly. Make sure you have a good ground, good power source, and the remote wire is run correctly. Also make sure the speaker output wires aren't touching each other, and you have the correct ohm load for the amp. What kind of speakers/subs are hooked up and how are they wired?

Sep 20, 2007 | Concept CC-2502 Car Audio Amplifier

Not finding what you are looking for?
Concept CD-2410 Car Audio Amplifier Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Concept Car Amplifiers Experts

Robert Rankin

Level 2 Expert

338 Answers

matthew walsh

Level 1 Expert

69 Answers

Tom Chichester

Level 3 Expert

24540 Answers

Are you a Concept Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...