Question about Washing Machines

1 Answer

Unknown message on display screen

What does the following mean when it appears on the display screen 'deno'

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I pressed the on button and the off button together. While I did this I pressed the left option button for a couple of seconds. The message disappeared and the washing machine is back functioning as it should.

Posted on Nov 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My washer error message unit detect a problem


The most common solution for this message is to turn the machine OFF and then ON. If the error resets, you are done.

However, this message will sometimes cause the control to stop the machine from working. With this type of error, the control panel will need to be reset. The following steps will allow you to reset your control.

Solution:

  1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.


  2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.


  3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.

Mar 02, 2015 | GE Profile WPRE6100G Top Load Washer

1 Answer

Stuck on "problem detected" screen


Hi deejay961...You may want to begin with the following procedures. Please update your post with your results, and if needed, we can progress until we correct your issue....good luck my friend...chris The Harmony washer electronics can automatically determine if problems exist with the machine. Sometimes an error code can also be present because of things the machine cannot control: like changes in house voltage, water pressure, or temperature. "A problem has been detected with this unit" will be displayed on the screen. The most common solution for this message is to turn the machine OFF and then ON. However, this message will sometimes cause the control to stop the machine from working. With this type of error, the control panel will need to be reset. The following steps will allow you to reset your control. Solution: 1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT. 2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in. 3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.

Aug 23, 2007 | GE WPGT9360EPL Top Load Washer

1 Answer

The letters DENO is chown on the display


Hello & Welcome to FixYa

The washer is in DEMO Mode and to deactivate it there are three ways depending on the age of unit:

1. Press Start/Cancel button untill all console LEDs illuminate....Then press both Start/Cancel and On/Off buttons together until d OFF appears on display.

2. Press the CANCEL button to cancel the DEMO mode.

3. Press the On/Off and Start/Cancel button together with the top left button option until the d Off appears

Please get back to me if you have any other questions.

Kevin

Jan 26, 2011 | Indesit WA 125 Front Load Washer

1 Answer

My ge profile harmony washing machine has a message that says "a problem has been detected with this unit."


Washers - Harmony Washer Error Message or Code
The Harmony washer electronics can automatically determine if problems exist with the machine. Sometimes an error code can also be present because of things the machine cannot control: like changes in house voltage, water pressure, or temperature.

"A problem has been detected with this unit" will be displayed on the screen.

The most common solution for this message is to turn the machine OFF and then ON. However, this message will sometimes cause the control to stop the machine from working. With this type of error, the control panel will need to be reset. The following steps will allow you to reset your control.

Solution:

1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.
2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.
3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.


GOOD LUCK. TIMOTHY DO 714-334-1998

Aug 04, 2010 | GE Washing Machines

2 Answers

Have a message on GE Profile Harmony washer that say " a problem has been detected with the unit" help?


Washers - Harmony Washer Error Message or Code
The Harmony washer electronics can automatically determine if problems exist with the machine. Sometimes an error code can also be present because of things the machine cannot control: like changes in house voltage, water pressure, or temperature.

"A problem has been detected with this unit" will be displayed on the screen.

The most common solution for this message is to turn the machine OFF and then ON. However, this message will sometimes cause the control to stop the machine from working. With this type of error, the control panel will need to be reset. The following steps will allow you to reset your control.

Solution:

1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.
2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.
3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.

Jan 15, 2010 | GE WPGT9360E Profile Harmony 4.0 cu. ft....

1 Answer

Display says deno


It appears your timer/main controller/CCU has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Apr 29, 2009 | Washing Machines

1 Answer

INDESIT 167 Stuk on DENO


It appears your timer/main controller/CCU has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question!!!!!!!!!!!!!!!!!!!

Jan 05, 2009 | Washing Machines

1 Answer

Indesit1200 front loader not filling and flashing error code deno can anyone help


hi try these
There have been 3 versions of Demo Mode used on these appliances.

Version 1(Production to- Date code 39 March 2005)

To Activate
1. From the Default screen of a programme, after switching the appliance on press both Start/Cancel and On/Off buttons together until d On appears in display.
2. Press the Start/Cancel button only and tESt appears in the screen (Temp & Spin symbols also appear)

To Deactivate

Press the Start/Cancel button until all the console LED's illuminate.
Press both Start/Cancel and On/Off buttons together until
d OFF appears.
The default screen returns and you can select a new programme.
Note:- The default screen information displayed on these models is that of the programme currently selected by the selector knob.

Version 2 ( during Date Code 39 March 2005- to Date Code 42 June 2005)

To Activate

1. Same method as version 1.

To Deactivate

1. Simply press the Cancel button and the appliance returns to default.

Version 3 (During Date Code 43 June 2005 - to date )

To Activate

1. Press On/Off and Start/Cancel together with the top left option button until d On appears.

To Deactivate

1. Press On/Off and Start/Cancel toghether with top left option button until d OF appears.

Aug 22, 2008 | Indesit Washing Machines

1 Answer

Hi i have a indesit wixe127 and when i switch it on it comes up with deno and will not wash wot is wrong with it


I had the same problem with DENO, while we run the wash machine i press start button and step easier(try the start button and click buttons simultaneously until the code DOF) button until DOF code came, after everything went well. e.ladislau@yahoo.com

Jun 19, 2008 | Indesit Washing Machines

1 Answer

INDESIT 167 Stuk on DENO


take the lid off the machine.remove or disconnect the wires off the main board giving them a small spray with a water dispersent or silicone based soloution.by the way turn the power off at the mains before carrying out this procedure.

Jun 29, 2007 | Indesit W 123 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...