An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert that has over 500 points.
An expert who has answered 200 questions.
Re: my kid power off tv by power button on tv, next time...
Switch tv on the switch can not contribute to that. unless the following goes fault
i switch getting fixed on one position(holding)
ii check power on a input of tv and input fuse
iii power supply, i have said that because if a power supply is ok, sound was going to be there.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
1. Turn on the TV or component.
2. Slide the MODE switch to the TV, AV1 or AV2 position, as desired.
3. Press and hold the MUTE and SELECT keys at the same time until the
green light under the selected switch position flashes twice, then
release both keys.
4. Enter 9-9-1 followed by one of the following four digits:
Satellite - 0
TV - 1
VCR/DVD - 2
Stereo Receiver/Stereo Amplifier - 3
5. Press PWR, or other functions (e.g. PLAY for VCR) you want to use.
6. Point the remote at the TV or component and press CHAN+. Repeatedly press CHAN+ until the TV or component turns off.
NOTE: Every time CHAN+ is pressed the remote advances to the next code and power is transmitted to the component.
7. Use the CHAN- key to step back a code.
8. When the TV or component turns off, stop pressing the CHAN+ key. Then, press and release the SELECT key.
NOTE: If the light flashes 3 times before the TV or component responds,
you've cycled through all codes and the code you need is not available.
Hi, tahnk you for visit fixya. Try this: ( two step)
1.--Unpluged power cord, push pwr button ( hold), connect the plug to AC line and wait for power up, release power button.
2.-- connect power cord, press power button, hold for 15 seconds, release power button.
Let me know if this work ok?. Any questions, I will be here. Thank you
If the TV standby light is blinking for five times then you may perform the steps given below: (i) Turn off the TV then disconnect all the cables from the TV. (ii) Next, reconnect all the cables after two minutes. (iii) Please make sure that the power cable from the TV is directly connected to a functional wall outlet. (iv) Next, you may try resetting the TV to the original factory settings.
Please follow the steps that are mentioned below to reset the TV to the original factory settings:
(a) Turn ON the TV. (b) Press and hold the Power button on the Remote Control supplied with the TV, then press the Power button on the TV front panel. (c) Release the Power button. The TV will turn itself off, then back ON again. (d) Next, release the Reset button on the Remote control.
If the standby light still blinks then the issue may be with the projection lamp in the TV and requires replacement.
the problem is that the tv was probably set to pwr on only with remote control.........i have the same problem and lost the remote...........BUMMER! Trying to figure out how to reset the programming without the remote.
Mike-It looks like the power supply is going on your tv-it can be replaced. This happens, usually, when little kids are playing wth the remote or power button on the tv. Turn it off and on a whole bunch of times in a row, kids love to do that, and it burns out the power supply part- to make a CRT tv like your RCA36 incher- which is a beautiful machine- I have the RCA/PROSCAN 36 incher-LAST longer...You should always wait 5 min between turning it off and on. Don't ever sell it. This one is worth fixing. It has better color and sound Than the new plasmas and lcds-The Pros know this. Be carefull, they might try and talk you out of it-so they can fix it and have it for themselves. So what if it's not High Deff. It's a great set.
after it fails how many times does the red LED blink? check the board very closely for any cracked solder. and then check the main regulators. also look to see if you have any physically bad capacitors, they might look like they are exploding on the top.