Question about Denon AVR-2803 Receiver

1 Answer

When dvd plays radio comes through as well.

If I select dvd to watch a dvd through amp, the radio comes through as well. Cannot listen to anything without another selection coming through. Has MULTI highlighted and I cannot separate. I changed dvd players and connected up through amp as per old dvd player and now have several selections playing at once. Even when I turn video off, radio will still come through if I select dvd. Can you help???

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

This unit needs to go out for service. There is an issue inside the circuitry in the unit.

Gary

Posted on Jan 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Sa-ex900 amp hooked up to Television ,vcr and dvd player. When I turn the amp on and want to play the tuner , the television bleeds through. In fact TV plays through all buttons except VCR1


Hi,
it seems to be ,you have a possible wrong connection..I
may I recommend you to check the connections in accordance with my model connection procedures given below and correct if something is misconnected..

I believe Your Television ,vcr and dvd player all connected to each other thru Technics Receiver itself (not directly connected to each other ) and whenever you want to listen/watch any of it ,you make a selection thru Receiver..
** in order to do this both DVD and VCR 's "2xRCA audio" and "1x RCA Video" cables for "IN" and "OUT" should go to Receiver separately ..("IN" goes to "OUT" of other ..pls remember,Always reverse connected )
** Additionally your RECEIVER's prefably only "1xRCA Video Output " should go to TV to watch the video of both DVD and VCR (audio will come thru Receiver.)

Ok, now Since you successfully connected your Receiver to play video on TV (one way only ) ,here is the second reverse action to listen your TV on Receiver
** you need to connect "Audio Output " as can either be : RCA jacks or "Optic cable output" or "SCART "connector " of your TV .( every TV has different type of Audio out jacks )
** to "TV input "or "AUX input" or "Optic Cable input"
of your Receiver (whichever you want ,based on the necessary cables on your hand )
** than just switch to respective mode on
Receiver corresponding the connector you have used on the back of Receiver ..
There you go..Tv sound are on the
Receiver .

Hope this helps!..if more help requires pls let me know.
Take care and please
Remember to rate/vote and give me 4 Thumbs Up for me to
continue f
or Helping out the Community :)

Jul 07, 2011 | Technics SA-EX900 Receiver

1 Answer

Input selection changing often by itself. e.g. while playing DVD, av receiver input selection change from DVD to CD then it comes back to DVD after some time automatically. I have reset the receiver by...


I'd suspect a poltergeist or a stray i/r source somewhere in your environment. You can prove the latter by blinding the receiver so it can't 'see' any remotes. Then just wait. If it behaves you have an unintended i/r source that it listens to. Security systems, garage door openers, sunlight...

May 22, 2011 | Onkyo TX-SR307 A/V Receiver

1 Answer

I have a LG47" tv


Your DVD audio is sent directly to your receiver - not to you TV. That's why you can hear the audio on your stereo. The TV audio is not being sent anywhere - it is "stuck" in the TV and is amplified and sent to the TV speakers. Since the TV speakers are off, you don't hear anything. In order to listen to the TV audio on the stereo system's speakers, you need to send it to the receiver.

You need to have a pair (left + right signals) of audio cables (assuming you wish to listen to stereo sound) from the TV's Audio Output jacks to a pair of Audio Input jacks on the receiver / amplifier. You can use any unused input - CD, Video, Tape, Sat, etc. If you use Tape or Sat audio inputs, when you wish to listen to the TV audio, you must select the Tape or Sat input on the receiver.

Do not send more than one signal to a set of inputs on the receiver. Typically, a CD, DVD and Sat inputs offer two or more of the following types 1) Analog audio. These are the older RCA jacks that have been around since the beginning and require separate cables for left and right channels. 2) Optical inputs. This is the newer digital interface that provides for Dolby Digital (and others) format sound over a single fiber optic cable. 3) Coaxial inputs. This jacks looks like an RCA jack, but usually has an Orange ring - instead of the Red & White rings that analog RCA jacks have. They use a single coaxial cable. 4) HDMI input. This jacks carries both digital video and digital audio signals. If you are using an Optical input for the DVD on the receiver, do not use any other unused analog or digital inputs associated with the DVD to "piggyback" another device like a CD , VHS tape, etc.

I hope this helps and good luck! Please rate my reply. Thank you.

Mar 25, 2011 | Audio Players & Recorders

1 Answer

While listening to DVD audio through the Amp, the audio muted with no selection on the remote. The mute light was not lit. Turned the amp off and then back on, the audio returned for 30 seconds, and then...


If I understand you correctly, you're listening to a DVD-A (high resolution audio) through the 5.1 analog inputs.

OTOH, if you're listening to a DTS soundtrack via a digital connection it will produce loud hash noise if played via analog means. You may have digital audio, stereo analog and 5.1 audio cables running from your DVD player to the receiver (I do). Look to see if the digital feed is dropping out. Three should be a light in the receiver to indicate 'digital'. The unit couldc be defaulting to analog stereo in the absence of a good digital bitstream.

Then you might want to look at the DVD player to make sure it isn't malfunctioning.

In this world of ripped portable music and earbuds it's nice to hear someone else appreciates high fidelity on DVD-A. Too bad the retail market for them and SACD died. I found dozens of them on eBay so at least I have a lot to listen to.

Aug 08, 2010 | Kenwood KRF-X9060D Receiver

1 Answer

No sound on regular t.v. and dvd, works with radio


Onkyo has a major problem with the hdmi module in this unit.hdmi pcb needs reolaced.

Apr 11, 2010 | Onkyo TX-SR606 Receiver

1 Answer

DTS option shows on the display when playing a DTS movie, but unit will only play in Dolby when trying to select listen mode...I can't select DTS mode


That is a typical function of the movie you are watching..changing the sound mode can "usually" only be done by selecting it on the disc, or by using the audio button on your player depending on the model.

Dec 23, 2009 | Kenwood VR-407 Receiver

1 Answer

I have a Denon 2308CI. I use the 7.1 suround. I have my sony STR DE995 to use as a second amp for zone two hook up. My goal is to watch a movie in the living room and listen to the radio or any other audio...


the mani surround room should be connected to the front speakers A, Center, sub pre-out and surround.
for the other two rooms connect them to surround/back, go into settings and in power amp assignment assign the surround back speakers to the multi room.
once this is complete with your remote in the zone2 control mode you can play your sources in zone2 and control the volume also, if you have inwall volume controls set the zone2 volume to -10 and use the room controls.
To listen to the same source in both zones you will have to select that source in both zones

Nov 16, 2008 | Denon Audio Players & Recorders

1 Answer

No Subwoofer sound with pro logic on TXSR503


When you are playing cd,s set your amp to stereo and the sub should work,prologic should never be used for playing music as this destorys the sound stage,if you are useing small speakers make sure you have set the size in the setup menu and the cross over to about 80hertz.

Hope this helps.

CABLE GUY.

Nov 16, 2008 | Onkyo TX-SR503 Receiver

1 Answer

Cannot hear DVD through the DVD receiver port


I had to turn on the TV first then the receiver and DVD player to see the video of the DVD.

Jul 31, 2008 | Onkyo TX-SR803 Receiver

Not finding what you are looking for?
Denon AVR-2803 Receiver Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Dennis McCollum

Level 2 Expert

137 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6370 Answers

Are you a Denon Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...