Question about Cross Infoguard Shredder SX102M

1 Answer

I have a SX102M paper shreder that wont shrede

The shreder wont shrede when you insurt paper however it will go in reverse the green light goes off when the paper tuches the switch

Posted by on

  • Anonymous Feb 24, 2009

    Shredder will not start in shred mode. Light is on but only operates in reverse.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It's the paper sensing microswitch. Wire a small toggle switch and drill a small hole for it on the far right side of the top housing. Just remember that the switch has to be turned off when you are finished shredding or the motor will keep running till it burns out

Posted on Feb 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I operate the equipment safely?


Just a few I can think of off the top of my head .

Do not over feed shredder - too thick = bad
avoid paper clips and staples going in
Avoid neck ties scarfs near shreder when other end around a neck
Avoid loose clothing near device that can fall into device.
Avoid plastic going in shredder
Make sure waste bin is not full before and while using device otherwise can strain motor.
Do not put water in device or wet paper
Do not operate near water or in rain
do not run shreder on wrong voltage and frequency check voltage from power point matches voltage and frequency required by shredder
do not put tree branches in shredder if designed for paper shredder
do not put cardboard in shedder

If paper gets stuck in shredder use reverse button and remove and try again with less paper . Do not forced shredder to drag paper through it.

Jun 02, 2015 | Office Equipment & Supplies

1 Answer

Infoguard-10 sx100m motor runs, sounds like gears are turning , goes both forward and reverse. i cleaned all of the teeth, looks clean, but won't accept paper. i am handicapped and am having a hard time...


Hello,

When motor is running, look to see if the cutters are turning. The cutters can be seen by looking into the throat of the shredder. If the cutters aren't moving, the gears may have been stripped and shredder needs to be repaired or replaced.

Good luck...

Apr 15, 2011 | Cross Infoguard Shredder SX102M

1 Answer

Works in reverse but not forward


Hi,

Move the power switch to AUTO (l) position and depress the manual forward button for five seconds to clear paper blockage. Make sure the paper is engaging sensor located in the center of the shredder opening.

Good luck.

Apr 11, 2011 | Cross Infoguard Shredder SX102M

1 Answer

Shreder works in reverse but not in forward.


Hello,

Check in opening and see if paper switch is stuck.

Dec 01, 2009 | Adler Royal HT500X Shredder

1 Answer

Paper jam. Ready lite comes on but shreder will not start shreding


Common problem with paper shreds blocking the sensors on top and bottom of cutter asm. You may have to remove the top of unit to properly clean. When removing top, be very careful with the short ribbon cable. Lift top slowly and then reach under and disconnect from main board. Once top is off, you can cycle motor by hand and try to remove shreds with needle nose pliers. Of course, disconnect power first.

May 15, 2009 | Tech Solution TS-4500 Shredder

1 Answer

Royal 9 x cross cut shredder wont go through even two pages thick


Put some shredder oil on the paper you are shreding...shred a number of sheets with oil on them so that the oil gets down into the cutting shafts/teeth.

Jan 12, 2009 | Royal Office Equipment & Supplies

2 Answers

Infoguard SX100M unit will not shred. Green light comes on.


I have the Infoguard SX100M Axeus, sold by Staples.
Only the reverse was working, UNPLUG and open back cover, the paper mechanical switch was working fine, red side switch, the gears and fuse were all ok, I think something on the circuit board was fried.

Anyways, I switched the BLACK and WHITE wires with each other going to the shredder motor, thus when I switched it to reverse, it would go foward and shred. Its working now, only in reverse.

Jan 10, 2009 | Cross Infoguard Shredder SX102M

1 Answer

Red overload light is on


Try pouring some shredder oil into the throat where you normally insert the paper and run the machine in reverse.Put machine back into ready condition.
Put a piece of paper in the throat just enough so the machine should run but not all the way in so that the cutting mechanism catches the paper...all you want to do is make the machine run forwards but not actually be feeding in any paper.
If it wont even run in the forward direction you may have a pcb prob...give Royal a call at 1-800-524-0799 for parts assistance.

Jan 08, 2009 | Royal VF1012mx Shredder

3 Answers

Sx-102M


I have the Infoguard SX-100M Axeus, sold by Staples.
Only the reverse was working, UNPLUG and open back cover, the paper mechanical switch was working fine, the gears and fuse was ok, I think something on the circuit board was fried.
I switched the BLACK and WHITE wires with each other going to the shredder motor, thus when I switched it to reverse, it would go foward and shred. Its working now, only in reverse.

Dec 21, 2007 | Cross Infoguard Shredder SX102M

Not finding what you are looking for?
Cross Infoguard Shredder SX102M Logo

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cross Office Equipment & Supplies Experts

gbob59

Level 3 Expert

2963 Answers

Jeremy Mordkoff
Jeremy Mordkoff

Level 1 Expert

4 Answers

k24674

Level 3 Expert

7993 Answers

Are you a Cross Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...