Question about Onkyo TX-DS939 Receiver

Open Question

Dsp56K9 ERROR CAN YOU HELP ME THANKS YOU PHILIPPE AIRY

Posted by on

  • Anonymous Dec 06, 2008

    same problem
    6 dec 2008
    do you resolved it



×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pioneer vsx 405 overloading whenever it turns on I checked the speaker wires and they are all OK.


vsx405 came error dc protection chacked all power transistors c2500 ,a1948 all ok i was disconnect dc detector wire then ok after few minutes one pair burned with c945100 ohms resistors that time not fix heat sink then all replaced power on error overload with speaker and without speakers also coming error disconnect ol wire no chang pease help any expert amplifiers thanks

Oct 27, 2011 | Pioneer VSX-405 Receiver

1 Answer

Hello. When we turn on our DVD player, it all of a sudden does not work. IT says "welcome" and OPen, but all at once flashes "protection" and shuts itself off. How can we fix this...


This is an error message which indicates that there is a hardware error on the circuit and needs correction and replacement before the feedback will reset the processor.
So you will need to disconnect the drive sections and see if the error message changes. If not there are shorting within the main board and needs a confirmation by elimination and voltage checking.

Mar 23, 2011 | Samsung Audio Players & Recorders

1 Answer

How to perform a master reset


Unhook all HDMI connections unplug the yamaha and your tv from the wall outlet then try again. Most cases a copy protection kicked in or the hdmi had a error on the port, Worse case is hdmi controller board failure in ether the TV or the yamaha.

thanks and do be considerate and leave postive feedback and ratings for those that have helped you today, Thanks

May 29, 2010 | Yamaha RX-V2600 Receiver

2 Answers

Protection error in denon avr-3000


Hi,

Do you know what caused the protection shut down in the first place? Did you short your speaker wires even briefly?

You could try to Unplug the Unit for Few Minutes, say 30 minutes and then turn it back ON.Usually that would fix the issue.

If you are going into protect mode with no speaker attached,chances are that your output Ic is in need of replacement .This is the most likely cause of a protection error that you are experiencing.I am having a bit of difficulty in locating specific part numbers but feel confident that replacing outputs will remedy your concern.For further info and parts or authorized service locations in your area I suggest to contact mfg at www.usa.denon.com/ .Click on support or call(201)762-6500.I believe that they have a flat rate service and will give you an estimate.

Still, on the remote possibility that it is just a glitch caused by momentary power interruption or fluctuation, try to re-initialize the microprocessor, a hard reset (not unless this is what you were referring to as rebooted). The reset should force the AVR-3300 to revert back to factory defaults removing glitches, errors in settings & configurations, memory & presets as well as user preferences.

* turn OFF the unit using the POWER button;
* press and hold both SPEAKER A and SPEAKER B;
* without releasing the 2 buttons, press the POWER button;
* release the 2 buttons only when the display starts to flash;
* in the event of no display flashing, repeat the process.


Should the above be not corrective, then it would be a hardware fault and not just a glitch.


Let me know, if needed further assistance.

Hoe i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Jan 13, 2010 | Denon AVR-3300 Receiver

1 Answer

Error 12 message on my sony multichannel av receiver str dg 510


error 12 is what you get if you autocalibrate and do not have the microphone attached.

Aug 23, 2008 | Sony STR-DG510 Receiver

1 Answer

Sa-ht545 error code f61- comes up upon statrting


No not that much.. but having it repair will be better than getting a new one..

Good luck.........

Jul 09, 2008 | Audio Players & Recorders

1 Answer

Tascam 2488 system error code 3


Hi jamie2488

The error code means different things depending on what version of firmware the 2488 is running. It will tell you when you first fire it up what version yours is running. Check out this

This is a list of all error codes, depending on the firmware. The code you are experiencing means you cannot duplicate to the same track(duplicate to a new or different track). To resolve (for v1.0) , press exit/no (for v1.01) press exit.

I am more than happy to answer any other questions you may have about it, just give me a hoy :) Thanks for using FixYa, If you consider the advice I have given you as sound, a FixYa rating is a great reward for my efforts to help you. Cheers.

regards
robotek




May 28, 2008 | Audio Players & Recorders

1 Answer

Cubase 4 Error Message


Same problem with audioprimitive.opt on Cubase 4

Mar 21, 2008 | Audio Players & Recorders

3 Answers

Stand by button flashes but receiver wont turn on


I have vsx-d812 that has an AMP ERR in error menu. the troubleshooting was found to be Q696 and Q697 in the DC prot. area on "C" board, up near front toward diplay in center of c board. You can get access to error codes on VSX pioneer unit by pressing "enter" and "adv. surr." simultaneously for 2 sec. The display should show what error code you are experiencing. I believe there are three diff. error codes. 1) AMP ERR 2) OVERLOAD 3) BOAD ERR (not mistyped) I hope this helps pinpoint error code for ya.

Oct 07, 2007 | Pioneer VSX-816-K/S Receiver

Not finding what you are looking for?
Onkyo TX-DS939 Receiver Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

Dennis McCollum

Level 2 Expert

137 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...