Question about Hitachi 43FDX01B TV

1 Answer

Green horizontal lines across screen

I have a Hitachi 43FDX01B that was made in 2000. It has several green horizontal lines across the screen. The lines start to curve at the edges on each side. Also, the overall color appears to have more of a green tint. Any idea what this could be & approx. cost of repair? We just spent about $400 on a different problem 6 months ago. Thanks.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 119 Answers
Re: Green horizontal lines across screen

Try adjusting the green screen control. remove the front bottom panel of the tv by removing any screws holding it in place. gently pull of the front panel, there are gromets holding it in place, you will be able to gently remove the front, just make sure you get all those screws. now reove the small wodden or plastioc panel. now you will see the screen/focus assy. check to see of the screen controls are the top 3 or bottom 3. adjusted the center screen it's the green one, the other 2 are the red & blue. it is best to adjust in a dark room where the lines will show up easier. good luck

Posted on Dec 19, 2006

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Hitachi UltraScan HD Projection Screen 43FDX01B

The convergence board is on the fritz! See and see if they have a kit just right for you!

Jan 12, 2010 | Hitachi 43FDX01B TV

1 Answer

Color has changed to green tint

    According to the system the problem in your projection is convergence and the solution is to replace the IC STK's.The part Number is CZ01341. Change the IC STK both and your TV work fine again.And for parts please see the link below.


Jan 09, 2010 | Hitachi 43FDX01B TV

1 Answer

I have a hitachi 43FDX10B ultrascand HD rear

well it seems to me that you need to call the manufacturer to see how to reset the pixels for that tv. it seems someone has taking a magnet or something like that to the tv screen

Nov 29, 2009 | Hitachi 43FDX01B TV

1 Answer

Red and blue convergence wont line up. What should i do.

convergance can be tricky and you should follow a manufacturers proceedure from a manual.

most specificaly start with the green H and V Linearity and center , then the Red and Blue

Projection TV's and Component Video RGB have their Horizontal and Vertical Sync signals on the Green Component..

There may be other reasons for their specific order of operations within a calabration proceedure such as your 'RGB convergance alignment'

Jun 16, 2009 | Hitachi 43FDX01B TV

1 Answer

Hitachi 43FDX01B green is out of whack

The green is not adjustable in the customer menu because it is considered the 'master' color. It is adjustable in the technician mode however but if it is curved it won't even adjust properly that way either. The problem is the convergence ampifier responsible for green convergence has failed. The convergence output IC's need to be replaced.

May 27, 2009 | Hitachi 43FDX01B TV

1 Answer

Single green line spanning across the screen horizontally

I was just watching TV and all of a sudden the screen minimized down to a single green line spanning across the screen horizontally. The label in the back says it was made in 1996 so it is an old tv. Can anyone help?

Apr 08, 2009 | Mitsubishi CS-27205 TV

2 Answers

Hitachi 43FDX01B Convergence Problems

Hitachi remote part # HL01643........I like the original remote
to do adjustments.................T.

Aug 06, 2008 | Hitachi 43FDX01B TV

1 Answer

Hitachi 43FDX01B TV Problem

if you have chirping sound .. check your horizontal out transistor that may be one cause there are seven or nine green lights around power supply see if all came on if not call me 520-248-4242 or leave message

Apr 16, 2008 | Hitachi 43FDX01B TV

1 Answer

Hitachi 43FDX01B (convergence) problem

Convergence IC's must be changed to start repair..original...
STK392-110 sub to Hitachi upgrade STK394-160E.....PART #
CZ need two....
Next, take a critical look at the B+ feed resistors near the IC's..
check for over-heat / damage......usually 2.2 ohm 2 watt......
Let me know....................T.

Jan 03, 2008 | Hitachi 43FDX01B TV

1 Answer

Hitachi 43FDX01B Green Line Not Alligned

If you slap the set on the side and the colors shift and dont line up, it is most likely that one of your convergence IC's has cracked solder joints. It is also possible that the IC has burned out. The convergence IC's will have to be resoldered and possibly replaced, and that should be done by someone with experience in repairing and realigning convergence circuits in projection TV's.

Aug 19, 2007 | Hitachi 43FDX01B TV

Not finding what you are looking for?
Hitachi 43FDX01B TV Logo

Related Topics:

344 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

66552 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1187 Answers

Are you a Hitachi Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides