Question about NEC MultiSync LCD1830 18.1" LCD Monitor

2 Answers

Power on Green but no display (blank screen)

I have a NEC MultiSync LCD1830 18.1" LCD Monitor and my screen went blank. I have replaced power cord and cables an still not working. Do you have any thoughts? cruzer

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers
Re: Power on Green but no display (blank screen)

In the LCD1830 the inverter for the backlight always burns out. They are fairly easy to replace when you remove the back to get inside. A new one is available from MoniServ for $69.99.

Posted on Apr 07, 2007

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 624 Answers
Re: Power on Green but no display (blank screen)

The first thing I would do is try another monitor if possible or take this monitor to another computer. If the problem follows the monitor then try shining a flashlight into the screen. If the backlight is out you will be able to see faintly the screen displaying your desktop. If you can?t see anything then the problem is more serious?. If the problem stays with the computer then we have a computer related problem. If you reboot do you see or hear anything?

Posted on Jan 02, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have an NEC '19 Multisync LCD 1920nx monitor. The display went blank and will not come back on. There's power going to it. It just doesn't display and image. How do i fix this?....thanks

more than likely it's not your monitor, but your graphics card. Do you have on board graphics or do you have a graphics card installed?

Aug 05, 2010 | Computer Monitors

1 Answer

NEC MultiSync LCD1765 won't power on

Look for bad caps with bulging top in the power supply first, post back what you see inside so we can guide you further, see example of failed monitors due to bad caps (after about 2 years):

Feb 15, 2010 | NEC MultiSync LCD1765 17" Flat Panel LCD...

1 Answer

NEC Multisync 1770gx lcd monitor goes blank when I move the unit


you must to check the volt at pin 1 of the lcd slot screen you'll get about 3.3 volts if not it can be the problem.


Jun 15, 2009 | Computer Monitors

1 Answer

No picture on monitor - green power light blinking

There's an internal electronic part/s of your monitor that is cold soldered / defective. I suggest to bring the unit to an authorized service center to properly diagnose & fix the problem. regards

May 28, 2009 | NEC MultiSync 75 17 in.CRT Conventional...

1 Answer

NEC MultiSync lcd 2010 monitor blank screen

This is the common bad capacitor problem. The caps have died inside, and they can be replaced. If you have basic electronics skills, you can go in, order replacement caps, and unsolder and resolder. If you can't do it yourself, you can take it into a shop.

Here is a link to the Cap plague that explains what happens in detail. But I repair these all the time with that symptom.

Apr 02, 2009 | NEC MultiSync LCD2010 20.1" LCD Monitor

1 Answer

My MultiSync LCD1810 Monitor stays on only for only 1 Second.

The Capacitor on the Inverter Circuit Board has gone bad and needs to be replaced. That's it.

Feb 17, 2009 | NEC MultiSync LCD1810X 18.1" LCD Monitor

2 Answers


the inverter board has a problem. this is the small pcb that sends high volts to the backlights you will need to change it

Jul 12, 2008 | NEC MultiSync 1525X 15" LCD Monitor

1 Answer

Problem with an NEC MultiSync 1550V 15" LCD

The power supply section may be failed, or there may be a short on one of the boards causing the monitor to cycle through the protect mode.

Jerry G.

Jun 02, 2008 | NEC MultiSync 1550V 15" LCD Monitor

1 Answer

Monitor displays breifly then goes to blank screen

F1 = Fuse 1
You should be able to locate a surface mount fuse at your local electronics store.

Apr 12, 2008 | NEC MultiSync LCD1830 18.1" LCD Monitor

Not finding what you are looking for?
NEC MultiSync LCD1830 18.1" LCD Monitor Logo

Related Topics:

573 people viewed this question

Ask a Question

Usually answered in minutes!

Top NEC Computer Monitors Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

William Miller
William Miller

Level 3 Expert

8795 Answers


Level 3 Expert

2598 Answers

Are you a NEC Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides