Question about Kenmore 95592 / 95594 / 95595 / 95599 Electric Kitchen Range

5 Answers

Kenmore electric range bake and broil burners come on

Kenmore electric range bake and broil burners both come on when turned on to bake only after replacing oven element which malfunctioned (Did not heat up)

Posted by on

  • hifi_2001 Nov 20, 2008

    replaced bake burner and control. wiring is correct to my knowledge both broil & bake elements turn on when baking there is no self clean option

×

5 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 367 Answers

The oven sensor should be your problem. But When you turn it to broil does the broil element get red or just warm? Did you buy the new element via your model number to make sure you got the exact one. Self clean elements are different than just bake elements. Does this have a digital oven control?

Posted on Nov 20, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 734 Answers

I think there is a fuse problem, because your element not getting power..

Posted on Nov 20, 2008

  • futureloginn
    futureloginn Nov 20, 2008

    first check the fuse.


×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Do you see an orange glow in the oven after you turn it on, but it doesn't lite?

Tell me quickly :)

Posted on Nov 20, 2008

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,806 Answers

Is there a fault code displayed?

Posted on Nov 20, 2008

  • Lee Hodgson
    Lee Hodgson Nov 20, 2008

    Pull the range out of the wall, remove the back covers and inspect all
    wires. Check the resistance across the oven sensor wires. It suppose to
    be about 1100 Ohms at the room temperature. Also check the hi limit
    thermostat for continuity.



×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kenmore Master
  • 19,396 Answers

WHEN YOU REPLACED THE ELEMENT YOU DID A WIRING WRONG. cHECK THE WIRINGS, AND CHECK THAT NO WIRING IS MAKING CONTACT, BOT ON ELEMENT AND ON CONTROL SIDE.

Posted on Nov 20, 2008

  • Ginko
    Ginko Nov 20, 2008

    Check the Element wirings, if there is a contact in there it can turn on both broiling and baking.

    If you touched the control assembly , then check also the wiring to the controls.

    Give me model number or insert model number here to get schematics.


  • Ginko
    Ginko Nov 20, 2008

    If you replaced the control, either the control is not the right replacement, or the broiling wiring on the control are wrong.
    The other possible option is that there is a contact where you replaced the element.
    Any contact on a different point of the lines is rather unlikely.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oven has power but none of the burners on top or the bake or broil elements work


Go to breaker panel,turn off and wait a minute and turn on,may reset it.

Oct 28, 2012 | Kenmore Kitchen Ranges

1 Answer

My oven wouldn't bake or bbroil but all burners


First suspect is the thermal fuse that feeds the bake and broil elements. It is located on the back oven wall or sometimes the top.

Jun 27, 2010 | Frigidaire FEF312 Electric Kitchen Range

1 Answer

Hi i have a kemore gas range that the bake ingiter or broil won`t


The igniter in the oven does not spark. It heats up and glows red hot until enough current opens the safety gas valve to the burner. It is not associated with the stovetop burners. Replace the oven igniter itself.

Aug 11, 2009 | Kenmore 79012 / 79014 / 79019 Gas Kitchen...

2 Answers

Kenmore electric range 790. Both the broil and


Kenmore oven 790.91072601, bake & broil not working, relays are cycling but no heat... Sounds like I have the same problem but its the night before Thanksgiving and Iam in panic mode... I've orderd a new Temp Probe part # 316233902. did you ever get yours fixed

Jul 13, 2009 | Kenmore Kitchen Ranges

1 Answer

Gas Oven


try to move your igniter close to burner or it may be loose

Nov 30, 2007 | Jenn-Air JDR8895AAS Dual Fuel (Electric...

1 Answer

Electric Kitchen aid, model kerc607...broil elements


What is the complete model # from the sticker on the range? I will need that so I can look into this for you. I will say that I have seen, in several cases, where the oven control gets a surge and fries after an element has broken.

Nov 10, 2007 | Kenmore 96212 / 96214 / 96219 Electric...

Not finding what you are looking for?
Kenmore 95592 / 95594 / 95595 / 95599 Electric Kitchen Range Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Cindy Wells

Level 3 Expert

4753 Answers

Mike Carew

Level 3 Expert

958 Answers

Are you a Kenmore Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...