Question about Printers & Copiers

1 Answer

My cannon printer won't print, it comes up with an error 600 and the alarm keeps flashing

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 685 Answers

Ok try unplugging it for about 10 minuets and plugging it back in.also check and see if there is anything stuck in it.let me know how this works

Posted on Nov 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cannon MX320 printer light are flashing both the on and alarm button - message contact service center, printer error has occurred at the botton of the sceen it shows B200


This error refers to a voltage problem within the print head. Usually the fix is a new print AND the main logic board.

Personally i feel its an end of life error and you should consider replacing the machine as the cost of repair is more than it would be to buy a new printer.

Sorry

Aug 25, 2011 | Canon PIXMA MX320 Color USB InkJet Printer

1 Answer

6A00 Error Code keeps coming up and the alarm light is flashing, I can't print anything how do I fix this please!!


Hi there !

6A00 is a problem with the sheet feed unit.

Here are a few suggestions to try.

1. Turn the printer off, and then back on.

2. Gently move the cartridge back and forth a bit.

2. Check for bis of paper in , around and under the cartridge

If this doesn't help, please reply to this solution with the model of Cannon printer you have.

Mar 11, 2011 | Canon Printers & Copiers

1 Answer

Cannon mx 310 error 5100 Says chck printr with alarm light flashi


heres the problem from service manual: error 5100, a error occured in your encoder signal, it list 4 things in the serice manual.
carriage unit. carriage motor, logic board, timing **** film.
ok my first thing i would look at is the film that runs directly behind the print head i would think it is dirty. just turn on printer and get print head to the middle and turn off machine, gentle move print head to one side and gentle clean the film strip with a cloth with a little metho on it, move print head to other side and clean other part of ****.
i reckon that will fix your problem its a common problem they tend to get a bit of grease on the timming ****.
Canon Tech

May 30, 2009 | Printers & Copiers

1 Answer

Receiving error message on display screen of mp500 code "6A00"


Hi
I think it the same code
The 6A00 is a Canon generic code for paper path jam.

Solution 1:
Move the printhead carriage back and forth a few times.

Solution 2:
Check the purge unit: Moving the print head assembly will not clear a purge unit if its jammed with paper, paper clips, push pins, screws, cookie crisp, flower bud pods or the like.

Solution 3:
Press the ink pads down in the purge unit.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Jan 05, 2009 | Canon Pixma MP500 All-In-One InkJet...

2 Answers

I have a cannon i9900, it has always worked perfectly. For the past week I can not print anything. I reinstalled software today still down, I see one green light followed by 5 yellow flashes (keeps...


Dear Bill,
Flashing 5 times in orange indicates that print head error occurs so it cannot be detected properly by the printer. To make it sure, install a good print head in the printer. Is the problem fixed?. If the problem still persist, carriage part may be faulty. Overall, the print head is the most faulty part in this case. So, you need to replace the print head with new one.
Regards,

Source:
Canon Inkjet Printer Forum

Nov 28, 2008 | Cannon Printers & Copiers

1 Answer

Alarm light is flashing and can not print


Hi
Try this
The 6A00 is a Canon generic code for paper path jam.

Solution 1:
Move the printhead carriage back and forth a few times.

Solution 2:
Check the purge unit: Moving the print head assembly will not clear a purge unit if its jammed with paper, paper clips, push pins, screws, cookie crisp, flower bud pods or the like.

Solution 3:
Press the ink pads down in the purge unit.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Nov 12, 2008 | Canon PIXMA MP830 All-In-One InkJet...

1 Answer

Canon MP240 will copy and print but will not scan.


cannon MP240 will not scan. my black ink alarm keeps flashing along with E,1,6 flashing. I'm out of black ink bit I'm just trying to scan photos. Do you know what this means and does it make a difference if I'm out of black ink to scan?

Thank you! Nikki

Nov 07, 2008 | Printers & Copiers

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Printers & Copiers Experts

kakima

Level 3 Expert

96372 Answers

old marine
old marine

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...