Question about Televison & Video

1 Answer

DLCD2602, TV SWITCHES ON BUT TRIPS AFTER A FEW SECONDS

Always trips back into standby, no picture or sound

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

It's like the power supply section problem. Please check all electrolytic capacitor inside the power section. Their ESR value also need to check to. Below is some good lcd repair site you can reference:

http://www.lcd-television-repair.com
http://www.fastrepairguide.com


Posted on Nov 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

While viewing a TV broadcast, TV "switches off" with a loud pop and goes into standby mode and will not respond to pressing the power button. Turn completely off, unplug, wait a while, then...


Good day!!!

normally,,that problem is caused of failing capacitors on the boards..

This is example picture of capacitor:
bugoy31_11.jpg

Follow this procedure on how to fix your TV..

  1. open the back cover
  2. look at the chassis/board inside your TV.
  3. try to look all capacitors inside..it likes the picture above..
  4. look at the actual image if it has a leak on oil/bulged on the top..
  5. try to replaced it with the same type,ratings and value.using soldering iron and soldering lead.
  6. after you replaced the bad capacitors..try to power it ON again to test if it is OK.
please watch this video for guide on how to replaced bad capacitors on the board.

Jul 16, 2011 | Pioneer Televison & Video

1 Answer

Trips and switches off


Hello Fixya customer,

Thank you for your question.

The best way to fully isolate the fault is to disconnect all the speaker wires, and verify that there are no strands of wire shorting between the speaker terminals on the rear of the unit.

Turn the volume all the way down, full CCW, and if it goes into shut down with the STBY light blinking then there is a fault in one of the amplifier's.

Thank you for using Fixya, and if I can be of further assistance please ask.

May 01, 2010 | Onkyo TX-SR706 Receiver

1 Answer

Samsung 50" rear projection tv switches off after a few seconds


probably need to replace the Ballast and Power Supply Board. If lamp has not been replaced, I would replace that too. can call 1-800-samsung for nearest service center.

Dec 29, 2009 | Samsung HLN5065W 50" Rear Projection...

1 Answer

My Pioneer PDP-435XDE was taken down to decorate the wall it is currently mounted to. When re-mounted and connected it happily goes from Standby to ON for about 10 - 15 seconds and then trips itself back...


did you try althe different inputs, maybe it's a unsupported signal being ent to the tv, liek a HD resolution that the tv doesn't support?

change the input and see if you can get anything to display. if the tv continues to go into ower up and standby no matter the input, it needs service.

Sep 10, 2009 | Pioneer PureVision PDP-435XDE 43 in....

1 Answer

Sony KF-60WE610 Screen and Sound On/Off


All symptoms in your TV shows that you need to replace its Lamp as it has been consumed its life hours and TV requires new lamp. Lamp can be obtained from Sony Website. Price is $200, Hope this info will help you to enjoy your Sony TV in coming days.

Aug 17, 2008 | Sony Grand WEGA KF60WE610 60" Rear...

1 Answer

LCD TV not working


im lokking for screen dlcd dual 2602

Mar 01, 2008 | Televison & Video

1 Answer

Sony 57 inch WEGA Projection TV


Hi, this is a very common failure, you need to replace 2 IC chips on your power supply board, marked on the top of the IC`s is this number: MCZ3001D you can purchase them here if you are very proficient at soldering & un-soldering, and the board has to come out of the tv to do this, you might want to call a tv man for this one, but it will fix your set, happy holidays, BMW Rider

Nov 29, 2007 | Sony Grand WEGA KDP-57XBR2 57" Rear...

1 Answer

Standby light flashing


I think that its some problem with your main board.so it is better to call your dealers

Nov 02, 2007 | Sony BRAVIA KDL-40S2010 40 in. LCD...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72271 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

yadayada
yadayada

Level 3 Expert

69244 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...