Question about HP Printers & Copiers

1 Answer

Simple- I just want to register my photosmartC5280 Help!!!!!!!~! pl e- I just want to register my photosmartC5280

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 77 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error display hc551 for Ricoh Aficio MP1600le, pl help me how it solve the problem.


Error code: 551 - Fusing thermistor open (rear)
The fusing temperature detected by the thermistor is below 71C and is not corrected after the main power switch is turned on.

Causes:
- Fusing thermistor defective or out of position
- Power supply board defective
- Loose connectors

Apr 29, 2015 | Ricoh Printers & Copiers

1 Answer

How to export in tally 7.2


This applies to Tally 7.2 and above.
1. You can export only registers and not masters
2. In any view register mode the export / import option becomes availble.
3. Click export.
4. Tally prompts you for a file name. The default name is always Tally.txt.
5. Pl rename the file to represent the ledger you are exporting else Tally will over write an existing file.
6. Tally will always save the file in the same drive / folder where Tally data resides. You cannot change this.
7. The file saved is the CSV file.
8. Open this file with Excel and map the fields.

Jan 20, 2015 | Tally Printers & Copiers

1 Answer

Xerox 4150 workcenter says fuser module needs to warm up. This appears usually first thing in morning. I have to power off then on to stop this from showing on the screen. also, it wont print until after I...


1. Switch off the machine, then switch on the machine.
2. Enter dC330 code 10-100 to heat the fuser to 180 degrees. Enter codes 10-200 (centre
thermistor) and 10-210 (front thermistor) to verify the condition of the thermistors.
3. Enter code 10-300 to check power supply unit 2. If necessary, install a new power supply
unit 2, PL 1.10 Item 4.
4. Switch off the machine. Remove the fuser assembly. Check that the thermistors, PL 10.25
Item 9 are clean and in good contact with the fuser heat roller. Check the wiring to the
thermistors. Install new components as necessary, PL 10.25.
5. Check for continuity between the two pins on the fuser assembly connector, PL 10.25
Item 8.
NOTE: A cold fuser has a resistance of approximately 11.5 ohms (220V/240V) or 2 ohms
(110V).
6. Check that there is continuity through the fuser heater and across the over temperature
cut-out.
7. Check the wiring between the fuser connector, PL 4.15 Item 20 and CON3, CON8 and
CON9 on Power Supply Unit 2. If necessary, install a new fuser connector, PL 4.15 Item
20.
8. Check the wiring between CON4 on Power Supply Unit 2 and CN7 on the Main PWB.
9. Install new components as necessary:
• Fuser assembly, PL 10.25 Item 1.
• HVPS, PL 1.10 Item 2.
10. Perform the OF5 Main PWB Check RAP.
4250/4260 Checkout
NOTE: The main PWB has test points. The location of the test points is shown on the Main
PWB PJ location illustration.
Refer to Wiring Diagram 17, Wiring Diagram 18 and Wiring Diagram 21. Perform the following:
1. Switch off the machine, then switch on the machine.
2. Enter dC330 code 10-100 to heat the fuser to 180 degrees. Enter codes 10-200 (centre
thermistor) and 10-210 (front thermistor) to verify the condition of the thermistors.
3. Enter code 10-300 to check power supply unit 2. If necessary, install a new power supply
unit 2, PL 1.15 Item 4.
4. Switch off the machine. Remove the fuser assembly. Check that the thermistors, PL 10.28
Item 9 are clean and in good contact with the fuser heat roller. Check the wiring to the
thermistor assembly. Check the wiring to the NC thermistor, PL 10.28 Item 19. Install new
components as necessary, PL 10.28.
5. Check for continuity between the three pins on the fuser assembly connector, PL 10.28
Item 8.
NOTE: A cold fuser has a resistance of approximately 11.5 ohms (220V/240V) or 2 ohms
(110V).
6. Check that there is continuity through the fuser heat lamps and across the over temperature
cut-out. Install new components as necessary, PL 10.28.
7. Check the wiring between the fuser connector, PL 4.15 Item 20 and CN5 on the Main
PWB. If necessary, install a new fuser connector, PL 4.15 Item 20.
8. Check the wiring between CON1 on Power Supply Unit 2 and CN7 on the Main PWB.
9. Install new components as necessary:
• Fuser assembly, PL 10.28 Item 1.
• Power supply unit 2, PL 1.15 Item 4.
10. Perform the OF5 Main PWB Check RAP

May 10, 2012 | Xerox WorkCenter 4150 Black and White...

1 Answer

Hello, My Epson R1800 is showing 2 red lights and I need to fix the problem but there is no communication between the printer and the computer - any advise on what to do? Your help is appreciated Many...


Dear User,

Pl check your printer driver installed correctly or not if not pl install with its cd.

printer and computer not communication by cable problem or computer or printer three types of cause.

pl printer install with another pc and check it.

Regards,

Ravindra shah

Jun 29, 2009 | Epson Stylus Photo R1800 InkJet Printer

1 Answer

Drum replacement


simple - service code 24-7 will rest drum, sevice 42-1 will rest deveolper service code 20-1 will reset serice indicators you can get a service manuel at persision roller in phx arizona and all parts

Feb 27, 2009 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

I require cannon g3 laser printer image class mf 5550 CD DISC


download the software from usa.canon.com

http://www.usa.canon.com/opd/controller?act=OPDDownloadIndexAct

Jan 21, 2009 | HP LaserJet 3300 All-In-One Printer

1 Answer

PhotosmartC5280 all-in-one, Will not scan to file


I lost my program to the scanner to scan to my computer. Help

Jun 20, 2008 | HP Printers & Copiers

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96467 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...