Question about Vacuums

1 Answer

My ink cartridge ran out of ink and I am unable to buy a new one right now so what should I do

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 107 Answers

I am assuming this problem is a printer not a vacuum. There really isnt anything you can do until then. You can use generic refill from walgreens but it is less quality than genuine ink. The refills also may leak or break but they are WAY cheaper

Posted on Dec 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I refill cartridge on mop?


The cartridge has a screw cap that you can open. Buy a gallon Bona floor cleaner and refill it.

Feb 17, 2016 | Bona Hardwood Floor Spray Mop W/...

1 Answer

Hi, I have a Casio fx-115s scientific calculator which I've had for around 25 years. I am unable to use the bracket function and have lost the instructions. Could you please give any advice to save me...


You should be able to use parentheses in the same order in which you would write the arithmetic expression. For example, 4*(3.5-1.5)= should give you 8. Without the parentheses, this would 12.5.

Essentially, the left parenthesis comes immediately after an arithmetic operator, and the right parenthesis must close the parenthetical expression right after a number, and an operator must follow the right parenthesis.

Apr 23, 2011 | Vacuums

1 Answer

Sock stuck in hose midway. Unable to getit out with wire or brrom handle. Is there a way to take hose apart at either end.


If the sock is midway, taking either or both ends apart won't help. Take it to a vacuum repair shop and ask them to try to unplug it. You may need to buy a new hose.

Feb 22, 2011 | Kenmore 23913 Progressive PowerMate Bagged...

1 Answer

Our Winsdor Sensor XP12 does not show any power or lights, I did check the handle connection, it was fine. The power cord has been repaired with duct tape 3-4 x where someone has sucked up the cord, this...


Any time the cord has been damaged badly enough to require taping, the possibility or intermittent "opens" exist. This means the wires are in contact much of the time, but will losed contact periodically. Even if it worked fine seconds ago, jiggling just right may cause this. This also presents a shock hazard.
I strongly recommend replacing the cord as soon as possible. If you are unable to do this, then please take it to a shop to be done.

Aug 31, 2010 | Windsor SR12 Sensor Bagged Upright Vacuum

1 Answer

I ran over one of my dogs toys and now the wheel will not turn over.


Go to amazon and buy a new piece and use instructions on how to fix it.

Feb 20, 2010 | Bissell 6594 PowerForce Bagless Upright...

3 Answers

Need belt for Everstar 5990 vacuum cleaner


I just replaced the belt on my Everstar VC-9550 and it works fine. I found it at Home Depot for $3.99. The belt is sold under Vac Belts item No. 51007 (Designed to fit Bissell Uprights, Style 7,9,10).

Apr 05, 2009 | Eureka 431A Optima Bagless Upright Vacuum

1 Answer

Broken/snapped off handle with minimal use...twice...two differen


Hi,
The shark has a one year warranty... send it back ...


Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...

Euro-Pro Shark Steam Mop Problem

Here also is a link to get any of the Shark Manuals that you need.

heatman101

Mar 04, 2009 | Euro-Pro Shark Steam Mop - Gray/ Purple...

3 Answers

Shop Vac just stopped


If you remove the motor, you will see that the wires that go from the switch to the brushes. On one side there is one wire connected directly to the brush. On the other side the wire goes to a plastic plug with a second wire going to the brush. This is probably where the problem is. This is a fusible link and it has most likely melted creating an open in the circuit. I put a piece of solder where the link was and the motor ran BUT the brushed arced like a sparkler. Upon further examination the brushes were crumbling apart. I have been unable to find replacement brushes.
This machine has a five year warranty. I called Shop Vac Customer Service 1-888-822-4644 and they sent me a new motor.
I had a Shop Vac QL50EIC which had exactly the same problem but the warranty was expired so that I had to buy another motor for about $50.

Mar 08, 2008 | Shop Vac 285-00-10 Back Pack Vac Wearable...

4 Answers

U5180-910 vacuum shuts off on own


I had same problem. Turned out to be the filter that sits above the waste cannister. Remove the waste cannister. There is a little orange lever that releases the filter. It was caked with dirt not allowing any air flow causing the motor to overheat.

This foam filter gets dirty pretty fast.

Nov 18, 2007 | Hoover U5180-900 Vacuum

Not finding what you are looking for?
Vacuums Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Roger Potts

Level 3 Expert

694 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...