Question about Jl Audio 1000/1 Car Audio Amplifier

1 Answer

500/1 settings to run jl13w6 v2 d-4

What are the amp settings for a 500/1 to run a jl audio 13w6v2 d-4 ! amp settings for subwoofer wired series ! an amp setting for sub wired parallel ! series would be 8 ohm an parallel would be 2 ohm ! an can this sub be run at 4 ohm an how ?

Posted by on

  • Anonymous Feb 28, 2009

    I HAVE TWO W7'S,12 INCH JL AUDIO AND A 1000v2 POWERED. I DONT HEAR ENOUGH BASSSS. CAN ANYONE HELP

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 226 Answers

Just had a look at both amp and sub on the JL Audio website. The amp runs from 1.5-4ohms. 4ohms at 14.5V. The sub is running dual 4 ohms coils. That's what the D-4 means. So should be an easy set up. The amp has two mono outputs, so one for each coil. It looks like the perfect wattage to run the sub real nice.
Web page for amp: http://mobile.jlaudio.com/products_amps.php?amp_id=439
Web page for sub: http://mobile.jlaudio.com/products_subs.php?series_id=18

Posted on Nov 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you hook up the speaker wire to the ab sub out and what is the best way to hook them up at what ohm


Not sure what you mean by AB but being that this is a monoblock or 1 channel amplifier you can only hook it up 1 way. Verify the polarity from your speaker box. + to + and - to -. As far as your impedance is concerned this amp is stable to 1.5 ohms but for this case we will assume you have two 4 ohm subwoofers. When you parallel these together you will have a total effective load of 2 ohms on the amplifier. This is a stable operating impedance for the amp.

Other impedance options are:

two 8 ohm speakers = 4 ohm load
three 8 ohm speakers = 2.66 ohms

If you have dual voice coil subwoofers then parallel the coils on each sub + to + and - to -. Depending on the impedance of each sub you may then have to wire the individual subwoofers in series. Here is an example.


2 dual voice coils with 4 ohm taps

Each subwoofer with the coils in parallel would be a 2 ohm load if you were to then parallel the two subwoofers together you would have 1 ohm total load on your amp. This is BAD for your amp. Your option is to run the subwoofers in series.

To run the speakers in series is simple. The + from one speaker and the - from the other will be connected to the amp. The other + and - from the speakers will be connected together.

Here is a wiring diagram from kicker.

http://www.kicker.com/dvc_wiring

Jun 11, 2011 | Jl Audio Slash 500/1 Car Audio Amplifier

1 Answer

I HOOKED EVERYTHING UP CORRECTLY BUT THE AMP WOULD ONLY STAY ON GOR ABOUT 20SECONDS THEN IT WOULD SHUT OFF. AFTER THAT WE TRIED ANOTHER AMP AND THAT ONE WOULDNT SHUT OFF. WHAT WOULD BE THE PROBLEM?


If the amp is a JL 500/1v2, it has a sensing switch which enables it to sense voltage, instead of running a remote wire. If this switch is set to on, and you have a remote turn on wire running to the amp........this can happen. I own one of these, and made that mistake myself.

Oct 18, 2010 | Jl Audio 500/1 Car Audio Amplifier

1 Answer

My Jl Audio 500/1, power light comes on but no power to subs


maybe it dont have enough to push it ,,did you try it before you buy it?

Mar 01, 2010 | Jl Audio 500/1 Car Audio Amplifier

1 Answer

How do i wire two audio pipe dvc woofers to this amp. do i use all four terminals on da amp. jl audio 500.1


Hello smoovek2008,

The JL Audio 500/1 outputs 500 watts RMS into a load from 1.5 to 4 ohms. Whether your subs have 2 ohm or 4 ohm voice coils, they should be wired in series and the subs paralleled to the amp. The final load to the amp will be either 2 ohms or 4 ohms, both of which the amp can handle. If you parallel the voice coils and then parallel the subs, the final impedance will be either 0.5 ohm or 1 ohm, both too low for the amp.

You can wire each sub to a separate set of terminals or both to the same set. The terminals are connected internally. It doesn't matter which of the +'s or -'s you use.

Hope this helps.

Sep 25, 2009 | Jl Audio 500/1 Car Audio Amplifier

1 Answer

JL A1800 Amp Not Switching On?!?


did you test for power at the amp, you should have 12 volts when the deck is on at the amp on the power and pto terminals. Also check and maybe reground the amp

Jun 05, 2009 | Jl Audio 1000/1 Car Audio Amplifier

1 Answer

Jl 500/1 amplifier will not turn on


you may have burned the channel you were using..try taking the cover off the amp and checkin for burned spots or any wires that may be loose or touching within the amp.

Feb 24, 2009 | Jl Audio 500/1 Car Audio Amplifier

1 Answer

Can i wire 3 jbl gto1204d subs into 1 jl audio 500/1 amp


You can connect them in a series/parallel configuration. Put two of them in series and then connect the last one in parallel across the two in series. This would give you an impeadance of around 2.7 ohms. Only do this if your amp is stable at 3 ohms or less. I am not familiar with the specs of your amp. If your amp is only 4 ohm stable you can not do this.
This would also give you half the power on the two subs in series as the power for the one that is parallel. The two in series would be sharing the total output signal, where-as the one in parallel would get the entire output signal from the amp.
if you were to connect a fourth sub woofer in this configuration it could give you a 4 ohm load, by adding the fourth sub in series with the single sub that is in parallel. or in other words, yu have two sets of 2 sub woofers each in series. That gives you two 8 ohm loads (two 4 ohm subs in series is 8 ohms). Then you take the two sets of subs and parallel them (two 8 ohm loads in parallel equals 4 ohms).

If i had a picture to show you it would make sense, two subs in series that are in parallel with two subs in series.

May 12, 2008 | Jl Audio 500/1 Car Audio Amplifier

3 Answers

How should I wire my 3 subs to the 500/1 amp???????


First of all how many ohm's are each subwoofer rated at . Are the subwoofers dual voice coil or single voice coil. Once I know that I can help you. I think the JL amp is not recommended below a 2ohm load.

Mar 16, 2008 | Jl Audio 500/1 Car Audio Amplifier

2 Answers

Speaker connections


This is a single channel amp that puts out about the same power at 4 Ohms or 2 Ohms. If you have two 4 Ohm single voice coil subs, then wire them parallel (both pos and both neg) to achieve 2 ohms. If you have two dual 4 Ohm voive coils, you want to do a series - parallel config to get to 4 Ohms (voice coils in series, then parallel the subs). Same with DVC 2 Ohm subs, series parallel = 2 Ohms. Do NOT go below two Ohms. You will blow the amp (actually, it'll do 1.5 Ohms). If you happen to have 2 Ohm single voice coil subs (not as likely) run them in series. Most amps will put out about twice as much power at 2 Ohms vs. 4, but this amp is designed to put out about the same. Hope this helps!

Feb 12, 2008 | Jl Audio 500/1 Car Audio Amplifier

Not finding what you are looking for?
Jl Audio 1000/1 Car Audio Amplifier Logo

Related Topics:

303 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jl Audio Car Amplifiers Experts

matthew walsh

Level 1 Expert

69 Answers

Tygh Duval
Tygh Duval

Level 2 Expert

290 Answers

Sudeep Chatterjee
Sudeep Chatterjee

Level 3 Expert

3267 Answers

Are you a Jl Audio Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...