Question about Symbol MC3090 Mobile Computer

1 Answer

No Laser Line from my MC3090BT

I pull the trigger on my Symbol Scanner and nothing happens. It has not been used for about a week and it has never been dropped. Any suggestions?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 65 Answers

There are three trigger buttons on the device, which one are you using? what application are you using? I can provide steps necessary for this request. You can always contact me directly akowalski@legacyglobal.com or 630-622-2024 toll free 866-271-9891 Ask for Andrew

Posted on Jan 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I turn on the red scanning laser on my Motorolla scanner MC9090


If it is working properly it should happen when you pull the trigger.

Manuals etc are located here:

MC9090 WM Mobile Computer Support Downloads Zebra

Jan 28, 2017 | Laser Computers & Internet

1 Answer

Pull trigger and nothing happens


Are you sure you have the safety key attached. Make sure power is on at receptacle.

Feb 09, 2014 | Ridgid Ms1065lza Saw 10-inch Compound...

1 Answer

MC9090 723100050044There is no laser light from trigger but ok from yellow centre button


BIZAAR BUT ONE OF MY CLIENTS IS SENDING ME ONE OF THESE UNITS IN FOR REPAIR TODAY....I THINK THE SCAN HANDLE TRIGGERS CONNECTION HAS BECOME DETACHED FROM THE CPU.... if you require assitacne please contact jack@codeo.co.uk or 00441179064587

May 17, 2011 | Zebra Symbol Technologies MC909X-G Series...

1 Answer

I have a barcode scanner Symbol S/N M1J82M51E. When scanning the item barcode it makes very low volume. How to increase the bipping scanning volume for the Symbol Scanner?


1. Press and hold the trigger for an extended period of time (approximately 5 seconds). The scanner cycles through three settings (Low, Medium, High) emitting a 2-beep tone at each setting.
2. To select a particular setting, release the trigger after you hear the desired 2-beep tone.

Sep 18, 2010 | Symbol LS9208 Hands Free Barcode Scanner

3 Answers

Hi, I'm writing a php page to be used on the MC9090 and I want the laser to be activated when focus is on a specific input box. Seeing as I'm new to the MC9090 scanner I don't have a clue where to start....


I'm not sure if you can trigger the scanner based on a web field but you can just enable the Data wedge software which will allow the scan to input anywhere you have the cursor. The scanner will be "active" all the time but won't actually scan until you pull the trigger. You can download the datawedge software from www.symbol.com.

May 19, 2009 | Symbol MC9090 Barcode Scanner

1 Answer

Symbol pdt3100; scanner is stuck in scan, laser will not release


It will either be the trigger or the scanner ribbon. More likely to be the trigger.

Mar 25, 2009 | Symbol PDT 3100

3 Answers

MC9060-G stuck in IPL (initial program loader mode.


Windows Active Sync will not recognise a scanner in IPL mode. You need to install the Symbol Device Configuration Package that is applicable to your scanner/cradle. Once installed and configured you can use SDCP to restore the Hex files needed for basic operation. All the files and loader software can be found at http://support.symbol.com/support/product/softwaredownloads.do
Good Luck

Oct 21, 2008 | Symbol MC9060-G

1 Answer

Laser does not trigger


open the OTL program.

go to 1 - Test Apps
go to 6 - Next Page
go to 1 - Auto Wedge On

do the tests now ;)

Feb 28, 2008 | Symbol MC1000 Barcode Scanner

1 Answer

Symbol LS 4278 Barcode Scanner - 3 Clicks


Does it beep each time you pull the trigger while the beem is on the barcode?

Jan 22, 2008 | Symbol LS 4278 Barcode Scanner

Not finding what you are looking for?
Symbol MC3090 Mobile Computer Logo

Related Topics:

692 people viewed this question

Ask a Question

Usually answered in minutes!

Top Symbol Computers & Internet Experts

Gareth Cockram
Gareth Cockram

Level 3 Expert

661 Answers

Greg Cann
Greg Cann

Level 3 Expert

1114 Answers

pkwc

Level 2 Expert

254 Answers

Are you a Symbol Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...