Question about Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

1 Answer

Start problem my smeg dwd1sse-1 starts for abt 1 sec,then stops,we had a recent power cut and i have cleaned the filters checked for blockage etc.

Posted by on

  • annie999 Jan 17, 2009

    our dishwasher has developed the same fault - no error code - just sarts and then defaults back to programme identifier on display.



    has anyone a solution?



    thx

  • Anonymous Feb 20, 2009

    our dishwasher has just started exhibitting the same behaviour, for example.

    a) set to a program ... say P4
    b) press the start button
    c) for about half a second, I hear a pump or motor or something go 'buzz' and a little water appears to be pumped out into the drain (a very small amount)
    d) the machine seems to 'reset' all stops, and the mahine just displays the program number again.
    e) at this point I can press start (b) and go around the loop ...

    does anyone have any ideas ? ... Yesterday it all worked fine :-(

    An ideas would be most welcome

    Ian

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hi
WE give this answer in good faith that anybody who benefits from it will make a donation to COMIC RELIEF, because I've just fixed my smeg d/w which is a great relief and no joke when not working,
SO DONATE.
My dishwasher tried to start but would not ,it tried but could not, the panel showed no fault.
The fault was caused by the failure of the solinoid (electric magnet) which opens the soap dispenser mechanism, located inside the door. I used an electric light up screw drive (from £ shop) which glows when you touch the end, to test the solioid, you could also use a multi meter though not as reliable.
We replace solinoid, (Common solinoid from any appliance repair shop) but I note on ebay there is a dishwasher guy selling the complete dispenser unit with new solinoid fitted.
Hope this helps( we have just had our first wash)
Do not forget to donate
Minnie Moon (twitter)
P.S. Sorry I can not remember how to spell solinoid (electro magnet)

Posted on Feb 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E5 smeg dishwasher


Water inlet solenoid valve faulty. Check this is voltage to valve when water should be flowing. Replace valve if there is voltage present.

Jun 04, 2014 | Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

1 Answer

Machine not takin any water


Before starting a washing program make sure that:
• The water supply tap is open.
• The correct amount of detergent has been added to the
dispenser.
• The baskets have been correctly loaded.
• The spray arms are able to rotate freely and without
obstruction.
• The dishwasher door is securely closed.

After you check all start the dishwasher again.

Jun 05, 2011 | Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

1 Answer

Won't empty


how old is it if its more the 1 year buy a new one but if its not just get it fixed

Jun 01, 2010 | Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

1 Answer

Smeg ST663 gets stuck onwash cycle


I have the same problem. If anyone has an answer I would be most greatfull.

Feb 11, 2010 | Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

1 Answer

Dirty dishes


check manual,your water hardness and salt/detergent quantities can make a big difference,theres usually some switches you can adjust for salt/detergent,if not check for partial blockage in pump etc,may be not enough water comming through.

Nov 02, 2009 | Smeg 18 in. DWI410 Built-in Dishwasher

1 Answer

Smeg Dishwasher ST 663 sometimes won't work


My dish washer stops after i5 minutes, don't know what the problem is, water is going in but just suddenly stops, i changed the hose but still the same. Any help welcome

Feb 22, 2009 | Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

2 Answers

Smeg code E8


I have exactly same problem. Have you solved it yet..

Aug 17, 2008 | Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

1 Answer

Smeg dishwasher tripping out fuseboard


Has the door got any heavier, as mine started tripping the electrics when a spring broke and short circuited the connections.
f so you will have to get the spring out, from the underneath is best and replace it if you want the door to work correctly again. On mine the second one went a month later.

Aug 07, 2008 | Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

1 Answer

Dishwasher won't start


Hi
WE give this answer in good faith that anybody who benefits from it will make a donation to COMIC RELIEF, because I've just fixed my smeg d/w which is a great relief and no joke when not working,
SO DONATE.
My dishwasher tried to start but would not ,it tried but could not, the panel showed no fault.
The fault was caused by the failure of the solinoid (electric magnet) which opens the soap dispenser mechanism, located inside the door. I used an electric light up screw drive (from £ shop) which glows when you touch the end, to test the solioid, you could also use a multi meter though not as reliable.
We replace solinoid, (Common solinoid from any appliance repair shop) but I note on ebay there is a dishwasher guy selling the complete dispenser unit with new solinoid fitted.
Hope this helps( we have just had our first wash)
Do not forget to donate
Minnie Moon (twitter)
P.S. Sorry I can not remember how to spell solinoid (electro magnet)

Aug 13, 2007 | Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

Not finding what you are looking for?
Smeg 24 in. DWD1SSE-1 Built-in Dishwasher Logo

412 people viewed this question

Ask a Question

Usually answered in minutes!

Top Smeg Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Starnley Johnwells
Starnley Johnwells

Level 3 Expert

1029 Answers

oysterman

Level 1 Expert

25 Answers

Are you a Smeg Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...