- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
well you need to reset your router wireless config, your isp dont do this, you need to config yourself, but i give some help. try these manual steps:
4.1 Log on the webpages
Open your Internet Browser
Enter http://192.168.2.1 in the address field
Click on GO
• The following webpage will be displayed
The only default language is English.
To access the required webpage, click on the corresponding tab on
the left side of the page. 4.2 Webpages’ menu structure The table below describes the menu tree of the webpages. 4.3 ADSL/Internet Settings webpages 4.3.1 ADSL status Click on "ADSL Status" which is located on the left side of the screen. SET UP WIZARD Getting started Wireless settings ADSL settings Confirm
The ADSL Wireless Base Station also operates as a wireless access
point, allowing wireless computers to communicate with each other. To
configure this function, you need to enable the wireless function, define
the radio channel, the domain identifier, and the security options.
Check Enable and click "SAVE SETTINGS".
You must specify a common radio channel and SSID (Service Set ID) to
be used by the ADSL Wireless Base Station and all of its wireless clients.
Make sure you configure all of its clients to the same values.
Access Control allows users to define the outgoing traffic permitted or
not-permitted through the WAN interface. The default is to permit all
If the signal strength of a single wireless base station is not sufficient due
to a large coverage area or attenuation due to walls, with WDS the
range of a wireless base station can be extended.
All base stations in a Wireless Distribution System must be configured
with the same radio channel, and encryption type (WEP/WPA) if that is
If you just typed in the IP address only then it won't work, you need to type "http://" in front of the IP address. Also for configuring wireless routers a LAN cable needs to be attached to the router and computer. This is removed after configuring the router, and these settings are used to configure the wireless card in the computer/laptop. The following various router configuring IP address are as follows :- Belkinhttp://192.168.2.1 Billion http://192.168.1.254 DLink and Netgearhttp://192.168.0.1 Linksys hppt://192.168.1.1 If you need further assistance please contact me with details, make and model of router, what steps you took and error messages.
For that you need to access your router configuration page. Connect your router to computer then access it with following link. For belkin router http://192.168.15.1 for other routers http://192.168.1.1 or http://192.168.0.1 type user as "admin" and password as "admin" or blank or "password" then you can see configuration of router. Click on wireless then check WEP or WAP key it is your password to connect internet. Let me know if you need further assistance. Thanks.
it sounds like you have a timer set on your router. you need to go to your routers configuration webpage by typing in the IP address in the web browser. Once you get to the router's webpage you need to go to access restrictions or something similiar to that. then you need to change the timer to your desired time you want internet then push save changes and that should hopefully fix it.
You have'nt specified whether your pc is connected to netgear or not. If yes then firstly it should be hard wired into the router to check connectivity.
Now on your PC Click start>run>type in cmd>in the command prompt screen that opens up type in ipconfig and press enter
it will display the ip address
if ip address is 192.168.0.2
and default gateway is 192.168.0.1 and still you're not able to open webpages run this command in the same command prompt screen netsh winsock reset catalog.......
You''ll be able to access webpages...
If ip address comes out to be something else get the drivers of nic card reinstalled on your PC.