Question about Sharp AR-5316 Advanced Digital Imager Copier

1 Answer

Display messege 4H how to solve pls - Sharp AR-5316 Advanced Digital Imager Copier

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Sharp Master
  • 2,794 Answers

Its an error indicating the fuser isn't at the right temperature. It could be a thermistor that went out. It should be looked at to see what needs to be replaced.

Posted on Nov 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Call for sevice 4H-00


enter the following on the machine ar-m207 #-___ * ________ C____* very fast the machine would display simulation then type 14 and OK,then press print button.press the press button consistently and machine restart by itself.

Dec 19, 2012 | Sharp AR-M207 All-In-One Laser Printer

6 Answers

Sharp ar 5516 printers error h5. h4


hi,I have error code L h on my coppier sharp 5516. your help please.

Aug 05, 2010 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

I have sharp 5316 it's giving error 4h


heater lamp&fuse ( broken heater)
RESET:clear -interrupt -0-interrupt
and 14 start-15 start

try the simulation about 5 times if not. u have to check fusing unit. so disconnect the two cables, turn it off then disconnect the power reconnect the cables put the power then on. so u have to do the simulation respectively..

4 00 Content Heat roller low temperature detection
Detail When the fusing temperature is lower than
150C° after 55sec from the start of warming
up.
When the warming up complete temperature is
not reached in 30sec from reaching 150C°.
When the fusing temperature is lower than
100C° after 20sec from ready start.
When the fusing temperature is lower than
145C° when printing."
Cause Thermistor abnormality
Heater lamp abnormality
Thermostat abnormality
Control PWB abnormality
Check
and
remedy
Use SIM 5-02 to check the heater lamp blinking
operation.
When the lamp blinks normally.
Check the thermistor and its harness.
Check the thermistor input circuit on the control
PWB.
When the lamp does not light up.
Check for disconnection of the heater lamp and
the thermostat. Check the interlock switch.
Check the power PWB and the lamp control
circuit on the MCU PWB.
Use SIM 14 to clear the self diagnostic display.

May 11, 2010 | Sharp AR-5316 Advanced Digital Imager...

2 Answers

My sharp copier AR-5316 has the problem. Error code 4H appear and cannot copy.


Hello sir; You need to do a reset procedure as follow; Press "#", "interupt", "C", " interupt". then enter 14 press start, machine go back to normal.

Oct 09, 2009 | Sharp AR-5316 Advanced Digital Imager...

4 Answers

Code H4 comes up when the sharp copier ar-5316 is switched on. it cannot be use. what shall I do to solve this problem of error code H4.


Hello sir; H4 code require reset procedure as follow;
1, press"#" "interupt" "c" "interupt" these 4 keys.
2, enter 14 , then press start
3, turn power off and back on .

Jan 28, 2009 | Sharp AR-5316 Advanced Digital Imager...

2 Answers

ERROR CODE 4H ON AR-5316


There is a problem with the fuser unit ( exit where it gets hot), unfortunately you need to replace
either 1- thermofuse, 2- thermistor, 3- heater lamp

Sep 10, 2008 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

Error code 4H


Performing a Fault Reset 14 will reset your WorkCentre and will help to clear error codes.
  1. Find the pink Clear button on the Control Panel of the WorkCentre.
  2. Find the button below the word Auto.
  3. Press these buttons in the following sequence: [Clear], [Auto], [Clear], [Auto] NOTE: All of the lights on the Control Panel should go out and the LED Display should go blank. If the lights do not go out, then repeat step 3 until they do. It may be necessary to increase or decrease the pace of the [Clear], [Auto], [Clear], [Auto] sequence.
  4. Press the [10's] key one time and the [1's] key four times to enter '14' in the LED Display, as if you were to make 14 copies.
  5. Press the green [Start] button.
  6. Press the pink [Clear] button two times.
  7. The WorkCentre should now warm up and come to ready.
  8. If the above steps do not clear the error code, repeat steps 3 to 6 a second time.

Apr 15, 2008 | Sharp AR-5316 Advanced Digital Imager...

Not finding what you are looking for?
Sharp AR-5316 Advanced Digital Imager Copier Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Printers & Copiers Experts

George Mclaughlin

Level 2 Expert

330 Answers

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Vito Suglio

Level 1 Expert

23 Answers

Are you a Sharp Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...