Question about JVC KABOOM RV-NB10 Boombox

1 Answer

Display light off

The display won't light up; can the bulb be changed? how?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

Yes it can, you`ll need a soldering iron, solder and a small 12 volt bulb , it is directly behind the display on a removable circuit board. You`ll need to bend the tabs straight and wiggle it off.

Posted on Aug 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

JVC RV-DP100BK orange backlit illuminate LCD display stop working?


You need a new bulb installed - difficulty is semi hard , in that you must take apart the boombox , remove the shroud around the bulb , unsolder , resolder new one ..take the old one to an electronics shop to match.

Apr 08, 2013 | JVC RV-DP100 Cassette/CD Boombox

1 Answer

The diplay will not work. Any suggestions?


Some displays have one or too bulbs that are solded to the board to highlight the digital display usually hidden behind the screen, this is a very difficult repair because it requires a complete dis-assembly to get at the parts, but if the display is completely dead there is no voltage reaching the display ic.

Jul 11, 2012 | Sony PSYC ZS-D55 Cassette/CD Boombox

1 Answer

How do i change the AM radio to FM?


Hello
Press RADIO BAND.AUTO PRESET until the band you want appears in the display (direct power on). Each time you press this button, the indication changes as "FM" --> "AM". Hold down TUNE + or --, until the frequency digit begins to change in the display. The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tuned in a station, press the button repeatedly to change the frequency step by step. If FM broadcast is noisy, press "MODE" until "Mono" appears on the display and the radio will play in monatural without any noise. Only strong FM signals can be decoded to stereo. OK.

Oct 22, 2011 | Sony CFD-S300 Radio/Cassette/CD Boombox

2 Answers

How do you auto preset radio stations?


Hello
[1] Press RADIO BAND.AUTO PRESET until the band you want appears on the display [direct power ON]. Each time you press the button the indication changes as follows. "FM" => "AM"
[2] Hold down TUNE+ or --ve until the frequency digits begin to change in the display.
The player automatically scans the radio frequencies and stops when it finda a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step.
If FM band is noisy, press the MODE repeteadly until "MONO" appears in the display and the radio will play it monatural. If FM radio signal at your area is very weak, this type of noise may occur. OK.

Sep 28, 2011 | Sony CFD-S350 Radio/Cassette/CD Boombox

2 Answers

How to program radio presets on sony cfd-s01


hold down the display/enter button until FM - 01 flashes. then press the display/enter button. The station you were tuned into is now preset #1

Dec 29, 2008 | Boomboxes

1 Answer

Display light


This is the backlight, bulb 9V. must be repaced, i suggest to replace by a 12V. bulb
Unit has to be disassembly. Good luck

Mar 03, 2008 | JVC RV-B55 Cassette/CD Boombox

1 Answer

Don't know how to set the time/clock.


Setting the Clock
Before operating the unit any further, first set the clock built
in this unit.
• When the unit is turned on with CD or tuner selected, press
DISPLAY first to show the clock indication.
1 Press and hold PROGRAM/SET
for more than 2 seconds.
The hour digits start flashing on the
display.
2 Press 4 or ¢ to adjust
the hour, then press
PROGRAM/SET.
The minute digits start flashing on the
display.
3 Press 4 or ¢ to adjust
the minute, then press
PROGRAM/SET.

If there is a power failure
The clock loses the setting and is reset to “AM 12:00.” You need to
set the clock again. If the batteries are inserted in the unit, this has
no effect on the memory.
To show the clock when CD or tuner is selected
Press DISPLAY.
• Each time you press the button, the display changes the clock
indication and the normal indication alternately. (Operating the
unit while clock indication is displayed change the display to the
normal indication.)

Feb 04, 2008 | JVC 10 Watt CD Boombox with AM/FM, Dual...

4 Answers

07 Armada


You will need to ask the dealer to replace the display again I'm afraid. I had a friend that had a similar problem with their Nissan. They had problems with display and the CD 4 times. If you try and do it yourself, that will void the warranty. Good luck

Dec 20, 2007 | Boomboxes

1 Answer

Bulb illuminating lcd display panel failed


go to an electronics store. You need a 12 volt bulb that solders onto a small removable circuit board located directly behind the display.

Dec 08, 2007 | JVC RV-B55 Cassette/CD Boombox

2 Answers

Display light out


Hello, I've had JVC RV-B90 Boombox for few yearst too, but display lighting is ok, There is just small bulb, so take it apart and just change bulg for new one. Good luck !

Jan 17, 2007 | JVC RV-B99GY Cassette Boombox

Not finding what you are looking for?
JVC KABOOM RV-NB10 Boombox Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Boomboxes Experts

Jonathon summesfield

Level 2 Expert

284 Answers

kakima

Level 3 Expert

96683 Answers

The Knight
The Knight

Level 3 Expert

68386 Answers

Are you a JVC Boombox Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...