Question about Arris DCT6200 DTV Receiver

1 Answer

Half of controls work

Nothing works except channel changing, volume, and on off button.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Flashman,

It sounds like the remote might be in TV mode and not CBL mode. When you press the List or Guide buttons, the CBL light on the remote should light up. If it doesn't, press the CBL button (located right under the master Power button) once, then try pressing List or Guide again.

Posted on Dec 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dish network Blue screen No "Signal


Hi john harrison!

A blue screen with "No Signal" is usually related to a video problem. The TV may be getting changed off the correct input/channel, or the video cable might be going bad.

If you have a spare, I would recommend a different cable and seeing if that fixes the problem. If it continues, verify the input/channel your TV is on when it receives a picture and if it goes out try putting it back on that input/channel.

If problems still continue I would be happy to review additional options with you. You can reach me here or at thomas.faust@dish.com

Tommy Faust
DISH Social Media Representative

Jun 03, 2012 | DISH Network TV Receivers & DVRs

2 Answers

I have a ViP722 DTV. I bought a new 52 inch sanyo LCD tv.\r\nI connected my Tv to the reciever using the "HDMI" cable. Programed the remote to run the tv and the DISH. All is fine! EXCEPT!!!! ...


I've had a few battles with Dishnetwork myself anfd the only thing you can do, if you want to keep the service is, 1 Pay a 15.00 fee for them to come out or, 2 Ge them o the phone and they will take you through a diagnostics with you which should end up with them sending you a new receiver in abox that you will put your old receiver in adn return it to them. I paid the 15.00 fee because I refused to go throuh the diagnostics over the phone. I've had mine replaced at least three times. Other than having to deal with them over the phone, I like the service and I had even bigger problems with Directv. If you already have changed your frequencies and that doesn't work, the only other thing you can try is pulling the piece out at the bottom of remote under where it says "dish Networks" and turn it over. The piece does come out. I'm pretty sure they will not let you out of your contract so you will end up with additional fees if you drop the service.

Apr 04, 2011 | DISH Network ViP722 DTV Receiver /...

2 Answers

Hi, I have an Aiwa A219 KE 21" color TV. Of late


Yes you have a dry joints on the croma,neck board section.
You need to resolder the cold solder first on the neck board (connected to the tube).
Then if nothing work there try to trace the connection of the wire from the neck to the main board.
Look for the dry joints around.Sometimes it is hard to spot so I've advice you to used a magnifying glass.
Thanks for using fixya.

Jan 23, 2011 | TV Receivers & DVRs

1 Answer

Charter remote will not change channels--I have put in tv code but still nothing--noting on the remote will work except to power the tv on


You will need to program it to your cable box to change channels. Remember, the channels in your tv are coming from your box, so if the remote can't control the box, you won't be able to change channels. Call charter for help on programming remote to cable box.

Jan 22, 2011 | TV Receivers & DVRs

1 Answer

Nikkai 2727 Video sender will not send signals from my sky+ box. The scart lead is plugged into the Video out, but even when i plug it into the TV out it still doesnt work. I know the Transmitter and...


check that you have the sender plugged into the sky box and the receiver into the required tv and not the other way round. The wrong way round still allows the controller to change channels but you will see nothing also ensure that both sender and reciever are on same channel 1 to 4

Jan 24, 2010 | Panasonic TV Receivers & DVRs

1 Answer

Cannot access channel 73 on TV2


If you are unable to access the TV menu using the buttons on the TV itself it is possible you can with the TV2 remote if it still controls the volume etc. for this TV. If it doe not you will need to find a code for your set in the manual for the receiver or you can go to the following link to find that info as well.http://tech.dishnetwork.com/departmental_content/TechPortal/content/tech/receiver/625.shtml
Assuming you have control of the volume still press the small TV button on the top left of the remote. Now press the menu button and you may be able to access the TV's menu. If so you need to run a channel scan/auto program the TV. You may need to use the buttons on the TV still to maneuver through the menu.
If you are still unable to access the menu you may need to purchase a universal to access the menu.

Jan 11, 2010 | DISH Network DVR-625 DTV Receiver /...

1 Answer

Black Box appearing on my screen


go into your menu and access the closed caption modes. someone has accidently put your tv in the "text" mode. turning off the closed caption feature will correct this.

Apr 01, 2009 | TV Receivers & DVRs

1 Answer

Just installed new tvonics250 freeview + box


Hi,

I have one of these boxes and one of the things which has caught me out a couple of times is that the remote can control three devices. To turn the Z250 on and off you may need to press the DTR button at the top of the remote first. When you press the on/off button on the remote the DTR button should light up red to let you know the signal is being sent to the Z250.

You are probably aware of this but just in case you weren't

Mar 02, 2009 | TVonics TV Receivers & DVRs

1 Answer

How do i program my remote


1. TV on.
2. On your Dish Network remote PRESS AND HOLD the small clear tv button until all buttons across the top of the remote light up and release.The only button lit should be the clear tv button that will be flashing.
3. Press the small red tv button next to the power button and release it. This should leave the clear tv button that was flashing lit solid.
4. Now slowly depress the channel up key until the tv turns off.Each time the up channel button is depressed the clear tv button will cease being lit and once it is released the clear tv button should remain solid. If the clear tv button flashes multiple times it usually means there is no known code for your tv, there may be another code that will work so continue on.
5. Once you are successful in getting the TV turned off press the channel down button once and then the channel up button. This should turn the TV back on.
6.Press the # key button on the remote. The clear tv button should flash three times then press the record button and try the volume up/down and the small red tv button. You should be able to turn volume up and down and turn tv on /off. If only one of these function it means that you have only found a half code and need to try the process again. Not all TV's have full codes or any codes at all especially combo units.

Aug 25, 2008 | RCA DISH Network(r) 311 Satellite System

1 Answer

Picture on TV stuck on one picture


Ok fixed it. Just unplugged the box and plugged it back in and it works fine.

Apr 05, 2008 | Directv Plus DVR DTV Receiver / 100-Hours...

Not finding what you are looking for?
Arris DCT6200 DTV Receiver Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Arris TV Receivers & DVRs Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68427 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Are you an Arris TV Receiver and DVR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...