Question about Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

1 Answer

Sensing light comes on and then the timer stop going down

I believe that it is a 2003 kenmore elite ultra wash. It seams to be cleaning the dishes, but a short time after the wash is started the sensing light will come back on and then the timer will stop going down. The washer will continue to wash for quite a while with the timer not going down. I shut the machine off after it washed for 20 to 25 min with the timer stuck at 76min.

Posted by on

  • Anonymous Nov 20, 2008

    Same problem, timer stops and the cycle keeps running, mare go for an hour or so. It may be the heating element or heating sensor may no longer work?? Help

  • Anonymous Feb 04, 2009

    I have exactly the same problem... but no solution. I have been running on time saver for more than a year now.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I do nto have a solution- just the exact same problem. My machine gets stuck on 76 when doing a "normal wash" . last night I hit cancel and drain, then went to "time saver" and ran the wash and it seemed to work fine. Funny that both of our amchines stop at 76. Any ideas?

Posted on Nov 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blinking clean light, not completing cycles


some of the dishwasher have a device in them that you have to remove the container and clean it. mine is up side down cup that unscrews.

go to www.wikipedia.org
kenmore elite blink clean light

or go on to www.sears.com/service
talk to someone or look on line at

www.youtube.com/kenmore_elite_blinking_clean_light

see if anyone else had this issue

Mar 25, 2015 | Kenmore 24 in. Elite Built-In Dishwasher...

1 Answer

My dishwasher will run and seems to clean but the panel is flashing. There is water sitting at the bottom and the panel shows red. Not sure how yo reset.


Check the filter and if equipped check the float in the bottom of the washer itself. Some of these circuit board will go bad and still function to some degree, but check the simple things first

Jan 11, 2015 | Kenmore 24" Built-In Dishwasher with Ultra...

1 Answer

My Kenmore Elite Ultra Wash Dishwasher keeps shutting off before entering the cycle. I have repositioned dishes, even emptied it, changed cycle and tried everything. When I press the start light flashes...


I too had problems with the Kenmore Elite (aka Bosch). The issue was solved by replacing the Lock Sensor on the door. After replacing the sensor the dishwasher has been working. Hope this helps.

Oct 08, 2013 | Kenmore Elite 24" Built-In Dishwasher with...

1 Answer

Water in bottom of kenmore elite ultra wash dishwasher


you must check the filters that are at the bottom under the spray arm
then you must start and then hold down cancel or stop and it should kick in the automatic water discharge mode and activate the water pump if this does not work you need new dishwasher pump installed which can be found online by googleing your model number. gut if this all works then the small flapper thats internal on the pump isnt sealing and allowing water to flow back into the bottom. last but not least you might need a new control board.

Nov 02, 2012 | Kenmore Dishwashers

1 Answer

Kenmore Elite dishwasher won't clean and leaves white film


CHANCES ARE YOUR WATER TEMP IS TOO COOL and the 2nd
PROBLEM IS VERY HARD WATER THAT IS CAUSING THE WHITE RESIDUE. RAISE THE TEMP ON HOUSEHOLD WATER TO 140 F AND ADD SOME SALT TO THE WASH CYCLE. LASTLY USE A LIQUID DETERGENT LIKE LIQUID CASCADE.

Oct 13, 2012 | Kenmore Dishwashers

2 Answers

I have an kenmore elite "ultra wash" model 665. not sure the rest.. about 7/8 years old, making loud buzzing sound during wash cycles,starts about 5 minutes into the normal wash cycle. i removed the inlet...


I have the same problem as those who stated their dishes are not getting clean. If you listen to the wash cycle you should hear water sloshing around inside. If you hear just a humming sound the washer has no water. I have this problem. I had a tech come and he told me the water is syphoning out my drain and I need to change my plumbing, then he charged me $65. I have lived in this house for ten years. 6 with the washer that came with house and 4 with this Kenmore Elite. This problem started about 6 months ago. So what I have been doing is opening the door, after the humming starts and the sloshing stops, and adding about 2 L of water. It seems to wash just fine after that.

Jan 12, 2010 | Kenmore 24 in. 17482 / 17484 / 17489...

1 Answer

K-more elite dishwasher stuck in sensing mode; won't move to wash


Where did you find the sequence to clear the flashing clean light?

Apr 14, 2009 | Kenmore Dishwashers

1 Answer

Green clean light keeps blinking


HI, Same thing happened to me today and Sears more than willing to charge me 200.00 for a 1 year service agreement. I found the answer on askmehelpdesk.com and the answer is: To reset a Kenmore Ultra Wash elite series dishwasher (stuck on clean) simply push heated/dry then normal wash and do the same thing again. Panel will reset itself and it hopefully will run normally again. Mine did and I am rejoicing! Julie

Aug 24, 2007 | Kenmore 24 in. 16302 Built-in Dishwasher

Not finding what you are looking for?
Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher Logo

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Fred Sops

Level 2 Expert

271 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Raisin Brann

Level 1 Expert

28 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...