Question about Watches

1 Answer

Winder button came off and the service # in the instuction manual

Does not work do you know who to call or where to get it fixed

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 100 Answers

Many local jewelry stores have a local/regional watchmaker to whom they send watches. You might try your downtown jeweler. OTOH, all of the chain jewelry stores have contracted with local repair folks for watches and jewelry. Take the watch to one of them and they'll "send it off" for replacement of the button. Depending on the brand/model of your watch, repair is likely to be a lot less expensive than replacing the watch.
I hope this helps! Please post rating, if it does.
Regards,
Char1ieJ

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Skagen manual 747lsxn


Stop the chrono with top button (if it is running) reset with bottom button. If hand does not zero pull out winder to position 2 and use top button to forward to zero by single steps or hold to move faster. #push winder back and chrono hand should be zeroed.

May 23, 2014 | Skagen Mens Sport 747LSXN

1 Answer

Problem with Cartier Tank Francaise W50005R2 Watch for Men


try this,,pull winder out to second position then press start button till it goes to 0 then push winder back in,,

Jan 05, 2013 | Cartier Tank Francaise W50005R2 Watch for...

1 Answer

I have a Fossill SpeedwayTitanium, the second hand doesn't work, i tried the fixya suggestion by pulling out winder and clicking the start stop button, with no sucess, it doesn't work


the module of your watch must be cleaned, bring it to watch service center, they have to see it and they really know what they are going to do with it.

Sep 09, 2011 | Watches

1 Answer

My tag heuer carrera stop watch doesnt reset properly, when u reset the stopwatch it goes one minute behind and doesnt reset to zero. how do i fix this. it never resets to zero and the red hands on the sub...


Try this.

Pull the winder out fully. Then press the top right chronograph button to move the centre seconds hand on. Then push the winder back in.

on some models you should only pull the winder half way out.

good luck

Sep 23, 2010 | Tag Heuer Carrera Tachymetre CV2013.FC6206...

1 Answer

Armitron did not come with a manual. I need


mcdevito75 here, No charge here at fixya for info unless you call on the phone. Does your armitron have buttons or a stem"" (winder). If a winder (stem) pull stem to it:"s first positon and set the date, then pull stem out all the way to set time. If buttons, press Mode ams see display blinking, press set on each function to cahnge them, Hour, Minute etc. after each function is set press mode to move to the next function, wfen done press mode again to return to staedy display. Hope This helps.

Jun 19, 2010 | Armitron 165 watch

1 Answer

Reset chronograph


Hi, I had the same problem and was able to fix it by reading the manual:

Basic Settings for the chronograph hand -
After changing the battery, or in exceptional circumstances, following incorrect operation, it is necessary to reset the Chrono indicator to zero (starting time).
- Leave the winder in Position 1 (pushed all the way in)
- Press button H (top) and button I (bottom) at the same time
- Now set the 30 minute (small hand) counter to zero by pressing/holding button I (bottom button)
- You can now set the 60 second counter to zero by pressing/holding button H (top button).

This worked for me... it took me a while to figure it out, but that

Jun 04, 2010 | Maurice Lacroix Masterpiece Flyback...

1 Answer

Resetting GMT hand


I have CL1180 and had the same problem, pulling the winder out to position 2 (fully out) and using the buttons resets the second and 10th second hands and putting the winder in position1 and using the buttons does the same for the minute and hour hands. However finding position1 was tricky, only seems to work on the way out from fully home and not on the way back from pos 2.

Hope that helps.

Apr 08, 2008 | Tag Heuer Aquaracer Quartz Chronograph...

Not finding what you are looking for?
Watches Logo

Related Topics:

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Watches Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Jimmy Accardi

Level 2 Expert

97 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...